Vestil EPFC-25-AA handleiding
Handleiding
Je bekijkt pagina 4 van 7
8/1/2016 EPFC-25-AA.docx
Copyright 2016 Vestil Manufacturing Corp. Page 4 of 7
Operation
Before using the crane, check the battery charge meter and confirm the battery is fully charged. Turn power on and test
the following: the horn, the controls for extending and retracting the boom, and the controls for raising and lowering the
boom. If all powered functions operate normally, the unit is ready for use.
Before the crane is loaded, perform the following:
verify the load is evenly distributed and safely secured
verify the crane will be operating on a level surface
Verify the transport distance is a short distance. The longer the distance the higher the risk of injury or excessive
drive system wear and tear.
Turn on battery power by pulling up on the power switch. Power switch is located on the dashboard, see item 2.3.
RAISING AND LOWERING THE BOOM: There are two buttons located on the right side of the handle. One is for raising
the boom. The other one is for lowering the boom. Make sure that there is no one standing near the truck or the load
while raising or lowering the boom.
TRAVEL CONTROLS: Two control wheels, one on each side of the belly switch, control direction and speed. Rotate
either control wheel away from you to drive the truck forwards. Rotate either control wheel towards you to drive in
reverse. The speed of travel is controlled by the degree of rotation in either direction, i.e. the farther you turn the
controllers the faster the truck moves.
BRAKING: This truck is equipped with an electromagnetic brake. The brake is applied whenever the control yoke is within
10~15 degrees of the vertical/home position or within 5 degrees of the lower position. The brake activates regardless of
the lateral (side-to-side) position of the yoke. Whenever the handle is released, it automatically returns to the vertical
position and activates the brake. Always confirm that the brake is in normal operating condition before using the truck.
EMERGENCY STOP BELLY SWITCH (item 1.7 ON p. 3): A red emergency stop feature, a belly switch, is located at the
top of the control yoke. When pressed and released, the switch interrupts drive functions which causes the unit to stop. If
the belly switch is pressed and held down, the unit will immediately reverse travel direction, away from the operator, for ~3
seconds. If the belly switch is pressed and quickly released, the unit will immediately stop. Before the unit will operate
normally after the belly switch has been activated, it must be reset. To reset functions, either move the yoke all the way
up, the yoke will also automatically return to the upright/home position whenever the operator releases the yoke, or all the
way down.
EMERGENCY POWER SHUT-OFF SWITCH (item 2.3 on p. 3): To turn power on, pull out the red button. To shut off all
power, travel, lift-lower, and extend-retract functions, press the button down. In an emergency situation, pressing the
button disconnects power and immediately stops all powered functions, unlike the belly switch which affects only the
travel, forward and/or reverse, functions.
HORN: A button for activating the horn is located on the top side of the control handle.
Specifications
Model
EPFC-25-AA
Capacity
2,500 / 1,300 / 600 lbs
Lift Height
45¼ - 130”
Lift
Speed
Loaded
1/2”/sec
Unloaded
0.70”/sec
Lower
Speed
Loaded
¾”/sec
Unloaded
¼”/sec
Travel
Speed
Loaded
2.18 mph
Unloaded
2.8 mph
Drive Motor
24V/700W
Lift Motor
DC24V/2.0KW
Battery
2x12V/70-80Ah
Battery Charger
24V/12A
Gradeability
0%
Overall size
79½x30x66⅜”
Bekijk gratis de handleiding van Vestil EPFC-25-AA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | EPFC-25-AA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1389 MB |
