Vestil EHLT-E-2448-2-41 handleiding
Handleiding
Je bekijkt pagina 13 van 17
TABLE OF CONTENTS Rev. 11/28/2022 EHLT-E MANUAL
TABLE OF CONTENTS Copyright 2022 Vestil Manufacturing Co. Page 13 of 17
Inspection procedures.
Prior to performing any inspection or maintenance on this lift table:
• Read and understand these maintenance procedures.
• Remove the load from the platform. Do not attempt to service
a loaded lift table.
• Fully lower the platform, OR use the maintenance prop to
support the weight of the platform. To use the maintenance prop,
raise the platform to its maximum height. Pivot the prop towards
the base frame. Lower the platform until the free end of the prop
solidly presses against the corner of the base frame.
• Disconnect power and follow established lockout/tagout
policies as required.
Initial inspection.
Before using any new, altered, modified, or repaired scissor lift table, it must be inspected by a qualified
person. Complete both the daily & monthly inspections before approving the lift table for regular use.
Daily inspection.
At the beginning of each shift, a designated person shall complete these inspections. Remove the lift
table from service and repair or replace any damaged parts if any of the following is found.
1. Look for:
a. Frayed wires.
b. Oil leaks.
c. Pinched, chafed, worn, or cracking hydraulic hoses.
d. Damage, deformation, or cracks in any structural member or any weld. Give special attention to the
hydraulic cylinder mounting brackets.
e. Loose or missing fasteners.
f. Unusual noise or evidence of binding.
2. Test the function of the upper travel limit switch.
3. Test the manual carousel (if applicable). Make sure that it rotates normally in both the clockwise and
counterclockwise directions. If the carousel is noisy, the load bearings should be replaced. Contact the
TECHNICAL SERVICE AND REPLACEMENT PARTS DEPARTMENT
.
Monthly inspection.
Have a qualified person inspect for:
1. Oil level. The oil should be 1” to 1-½” below the reservoir fill hole with the platform in the fully lowered
position. See the Annual Inspection section for the hydraulic oil specification.
2. Worn or damaged hydraulic hoses or electrical wires.
3. Wear in the pivot points on the legs.
4. Looseness or wear in the rollers.
5. Integrity of the retaining hardware on all rollers and all pivot point pins.
6. Integrity of the frame anchor bolts, and for cracks in the concrete around them.
7. Proper functioning of hand- or foot-operated mechanisms.
8. Unusual noises or movement during operation.
9. Condition of all information, safety, and warning labels. These should be clean and clearly legible.
10. Dirt and debris. Clean, sweep, or wipe down as needed.
Annual inspection.
Check the condition of the oil. Change the oil if it darkens, becomes gritty, or turns a milky color
(indicating the presence of water). Replace with an anti-wear hydraulic oil with a viscosity grade of 150 SUS
at 100°F (ISO 32 cSt @ 40°C), such as AW 32, HO 150 or Dexron non-synthetic transmission fluid. You may use
a synthetic transmission fluid if you flush the system with the synthetic fluid before filling the reservoir. 150 SUS
at 100°F (ISO 32 cSt @ 40°C) or Dexron transmission fluid.
Deploy maintenance in base frame
Bekijk gratis de handleiding van Vestil EHLT-E-2448-2-41, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | EHLT-E-2448-2-41 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3585 MB |
