Handleiding
Je bekijkt pagina 13 van 19
EN - 13
4. USE OF PRODUCT
4.1 hob ControlS
The hob is controlled by pressing the
appropriate electronic button. Each button
pressed is followed by a buzzer sound.
1
3
4
5 6
7 8
2
1- Heater display
2- Activate/Deactivate heater
3- Heat setting decrease
4- Heat setting increase
5- Decimal point
6- Key lock indicator
7- Key lock
8- On/Off
Mode Descriptions
Stand-By-
Mode
S-Mode
Mains supply is applied to
the hob control and all
heater displays are off or a
residual heat display is
active.
Operating-
Mode
B-Mode
At least one heater display
shows a heat setting between
´0` and ´9`.
Lock Mode
VR-
Mode
The hob control is locked.
Switching the Appliance On and Off
If the appliance is in Stand-By mode, it
is put in Operating mode by pressing the On/
Off button for at least 1 second. A buzzer
will sound to indicate the successful operation.
A “
0” will appear on all heater displays and all
decimal points corresponding to the heaters will
flash (1 second on, 1 second off).
If there is no operation within 10 seconds, all
heater displays will switch off.
If the displays do switch off, the heater will be
sent into Stand-By mode.
If
is pressed for more than 2 seconds
(in Operating mode), the appliance will switch
off and will enter S-Mode again. The appliance
can be switched off by pressing
at any time; even if other buttons are
pressed simultaneously.
If there is any residual heat from a heater, this
will be indicated in the corresponding heater
display.
Selecting a Heater
If a single heater is chosen with the
corresponding Activate/Deactivate Heater
Button , the decimal point of the heater
display will flash. For the selected heater, you
can set the heat level between 1 and 9 by
pressing the Heat Setting Buttons
or .
The buttons must be pressed within 3 seconds of
selecting a heater, otherwise the heater selection
will be erased and the heat setting decimal point
will disappear. If there is no further operation
within 10 seconds, the heater reverts back to S-
Mode.
The heat setting can always be changed by
pressing or . The available settings are
between 1 and 9.
Each button operation or each display change is
accompanied by a buzzer sound.
Set Cooking Level with and without Heat Boost
All heaters are equipped with the heat boost
function.
If the heat boost is required, set the heat from
the current level to level 9 by pressing the
button only. Once level 9 has been reached,
press to activate the heat boost. The display
will flash “A” alternating with the heat setting
value “9” to show the heat boost is active.
If the heat boost is active, the heater will
operate with maximum power for a period of
time dependent on the heat setting selected
before the heat boost was activated.
Once the heat boost time has ended, only the
heat setting will be indicated on the heater
display.
The heat boost can be deactivated by pressing
until the heat setting “0” is displayed.
Switching Off Individual Heaters
A heater can be switched off in 3 different ways:
• Simultaneous pressing of and
buttons
• Reduction of the heat setting to ´0` by
pressing the button
• Use of the timer switch-off function for the
corresponding heater.
Bekijk gratis de handleiding van Vestel AO-6330 B, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestel |
| Model | AO-6330 B |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 1221 MB |
