Verto 52G584 handleiding
Handleiding
Je bekijkt pagina 13 van 112
13
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
CHAIN SAW
52G584
CAUTION: BEFORE USING THE CHAIN SAW READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
CHAIN SAW SAFETY WARNINGS:
• Hold the power tool by insulated gripping surfaces only,
because the Saw chain may contact hidden ring. Saw chains
contacting a ,,live” wire may make exposed metal parts of the power
tool “and could give the operator an electric shock.
• Keep all parts of the body away from the saw chain when the
chain saw is operating. Before you start the chain saw, make
sure the saw chain is not contacting anything. A moment of
inattention while operating chain saws may cause entanglement of
your clothing or body with the saw chain.
• Always hold the chain saw with your right hand on the
rear handle and your left hand on the front handle.
Holding the chain saw with a reversed hand conguration
increases the risk of personal injury and should never be done.
Note: For chain saws designed with the guide bar on the left side,
the reference to ,, right hand” and ,,left hand” positioning is reversed.
• Wear safety glasses and hearing protection. Further protective
equipment for head, hands, legs and feet is recommended.
Adequate protective clothing will reduce personal injury by ying
debris or accidental contact with the saw chain.
• Do not operate a chain saw in a tree. Operation of a chain saw
while up in a tree may result in personal injury.
• Always keep proper footing and operate the chain saw only
when standing on xed, secure and level surface. Slippery or
unstable surfaces such as ladders may cause a loss of balance or
control of the chain saw.
• When cutting a limb that is under tension be alert for spring
back. When the tension in the wood bres is released the spring
loaded limb may strike the operator and/or throw the chain saw out
of control.
• Use extreme caution when cutting brush and saplings. The
slender material may catch the saw chain and be whipped toward
you or pull you o balance.
• Carry the chain saw by the front handle with the chain saw
switched o and away from your body. When transporting
or storing the chain saw always t the guide bar cover. Proper
handling of the chain saw will reduce the likelihood of accidental
contact with the moving saw chain.
• Follow instructions for lubricating, chain tensioning and
changing accessories. Improperly tensioned or lubricated chain
may either break or increase the change for kickback.
• Keep handles dry, clean, and free from oil and grease. Greasy, oily
handles are slippery causing loss of control.
• Cut wood only. Do not use chain saw for purposes not intended.
For example: do not use chain saw for cutting plastic, masonry or
non-wood building materials. Use of the chain saw for operations
dierent than intended could result in a hazardous situation.
CAUSES AND OPERATOR PREVENTION OF KICKBACK:
Kickback may occur when the nose or tip of the guide bar touches an
object, or when the wood closes in and pinches the saw chain in the
cut. Tip contact in some cases may cause a sudden reverse reaction,
kicking the guide bar up and back towards the operator. Pinching
the saw chain along the top of the guide bar may push the guide bar
rapidly back towards the operator. Either of these reactions may cause
you to lose control of the saw which could result in serious personal
injury. Do not rely exclusively upon the safety devices built into your
saw. As a chain saw user, you should take several steps to keep your
cutting jobs free from accident or injury. Kickback is the result of tool
GB
misuse and/or incorrect operating procedures or conditions and can
be avoided by taking proper precautions as given below:
• Maintain a rm grip, with thumbs and ngers encircling the
chain saw handles, with both hands on the saw and position your
body and arm to allow you to resist kickback forces. Kickback
forces can be controlled by the operator, if proper precautions are
taken. Do not let go of the chain saw.
• Do not overreach and do not cut above shoulder height. This
helps prevent unintended tip contact and enables better control of
the chain saw in unexpected situations.
• Only use replacement bars and chains specied by the
manufacturer. Incorrect replacement bars and chains may cause
chain breakage and/or kickback.
• Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain. Decreasing the depth gauge height
can lead to increased kickback.
• Persons unfamiliar with instruction manual are not allowed to
use chain saw.
• Other use of the chain saw is the sole responsibility of the user
who should bear in mind that it may be dangerous.
• The manufacturer is not responsible for losses and damages
resulting from unintended use of the chain saw.
• Carrying the chain saw is possible only when holding its front
handle. Other parts may not ensure appropriate grip and even cause
injury.
• Cutting chain should be clean and sharp. Proper maintenance of
sharp cutting edges of chain reduces the risk of jamming and makes
operation easier.
• Check proper operation of the saw brake regularly. In emergency
situation, non-operational brake may make chain disengagement
impossible.
OPERATION
• Be very careful at the end of a cut, because the saw having no
support in processed material falls down due to its inertia, which
may cause injuries.
• When working for a long time, the saw operator may experience
formication and numbness in ngers and hands. Stop working in
such case, because numbness reduces precision in saw use.
• The saw heats considerably during operation. Be careful and do not
touch hot parts of the saw with unprotected parts of your body.
• Only one person can operate the chain saw at a time. All other
persons and animals shall be away from working area of the chain
saw.
• When starting the saw, its cutting chain must not rest on the
processed material.
• Children and juveniles cannot operate the chain saw. Allow only
adults who know how to handle the tool to access the saw. This
instruction manual should be given with the chain saw.
• Stop working with the chain saw with rst signs of fatigue.
• Before starting to cut set the chain brake lever in appropriate
position (pull it to yourself). It is also hand guard.
• When cutting sawn wood or thin branches use support (sawing
horse).
• Do not cut several boards at the same time (placed one on top of
another), or material held by other person or held with foot.
• Long objects should be rmly xed before cutting.
• On sloped terrain process with cutting only when facing towards top
of the hill.
• When cutting through always use the bumper spike as a point of
support. Hold the saw by the rear handle and guide with the front
handle.
• In case the cut cannot be completed in one run, slide the saw out,
position the bumper spike and continue the cut by lifting rear
handle.
Bekijk gratis de handleiding van Verto 52G584, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Verto |
| Model | 52G584 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 17843 MB |
Caratteristiche Prodotto
| Kleur van het product | Green, Stainless steel |
| Geluidsniveau | 105.3 dB |
| Stroombron | AC |
| Vermogen | 2000 W |
| Stationair toerental | 12.1 RPM |
