Tunturi Signature T50 handleiding
Handleiding
Je bekijkt pagina 14 van 56
14
English
End of life disposal
We at Tunturi hope you enjoy many years of
enjoyable use from your fitness trainer. However,
a Time will come when your fitness trainer will
come to the end of its useful life. Under ‘European
WEEE Legislation you are responsible for the
appropriate disposal of your fitness trainer to a
recognised public collection facility.
Use
Master power switch (fig� E-2A)
The equipment is equipped with a master power
switch to shut down the equipment completely.
To start the equipment:
- Insert the mains plug into the equipment.
- Insert the mains plug into the wall socket.
- Set the master power switch to the on position.
To stop the equipment:
- Set the mains power switch to the off position.
- Remove the mains plug from the wall socket.
- Remove the mains plug from the equipment.
Safety key (Fig F-4)
The equipment is equipped with a safety key that
must be properly inserted into the console to start
the equipment. If you remove the safety key from
the console, the equipment will stop immediately.
- Insert the safety key into the slot in the console.
- Make sure that the clip of the safety key is
properly attached to your clothing.
Make sure that the clip is not removed from
your clothing before the safety key is removed
from the console.
‼ NOTE
• Console will show E7 code when safety key is
not in (correct) position during start up.
Circuit breaker (Fig� E-2B)
The equipment is equipped with a circuit breaker
that interrupts the circuit when the electricity load
is above the maximum capacity. When this occurs,
the circuit breaker must be pressed.
⚠ WARNING
• Before pressing the circuit breaker, remove
the mains plug from the equipment.
If the equipment shuts down, proceed as follows
to restart the equipment:
- Remove the mains plug from the equipment.
- Press the circuit breaker to restart the
equipment.
- Insert the mains plug into the equipment.
‼ NOTE
• Some circuit breakers used in homes are
not rated for high inrush currents that can
occur when a treadmill is first turned on or
even during normal use. If your treadmill is
tripping the circuit breaker (even though it is
the proper current rating and the treadmill
is the only appliance on the circuit) but
the circuit breaker on the treadmill itself
does not trip, you will need to replace the
breaker with a high inrush type. This is not a
warranty defect. This is a condition we as a
manufacture have no ability to control.
Unfolding and folding the
equipment (fig� F1-F2)
The equipment can be unfolded for use (fig. F1)
and folded for transport and storage (fig. F2).
Refer to the illustrations for the correct way of
unfolding and folding the equipment.
⚠ CAUTION
• Before folding the equipment, make sure that
the incline is 0. If the incline is not 0, folding
will damage the mechanism.
Adjusting the support feet
The equipment is equipped with adjustable
support feet.
If the equipment feels unstable, wobbly, or not
levelled well, these support feet can be adjusted
to make the required corrections.
- Turn the support feet in/ out as required to put
the equipment in a stable and as well possible
levelled position.
- Tighten the locknut’s* to lock the support feet.
QUIC TIP
• It is easier to do this with two persons, so
one person can tilt the equipment, while the
other makes the needed adjustment.
Click to see our supportive YouTube
video
https://youtu.be/E_7agKqaUIc
Bekijk gratis de handleiding van Tunturi Signature T50, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tunturi |
| Model | Signature T50 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6896 MB |
