Tryton TMB1500K handleiding
Handleiding
Je bekijkt pagina 6 van 56
6
and shock the operator.
l) Position the cord clear of the spinning accessory. If you lose
control, the cord may be cut or snagged and your hand or arm may be
pulled into the spinning accessory.
m) Never lay the power tool down until the accessory has come
to a complete stop. The spinning accessory may grab the surface
and pull the power tool out of your control.
n) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
o) Regularly clean the power tool's air vents. The motor's fan will
draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
p) Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
r) Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or shock.
FURTHER SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Kickback and Related Warnings:
Kickback is a sudden reaction to a pinched or snagged rotating wheel,
backing pad, brush or any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction opposite of the
accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch point can
dig into the surface of the material causing the wheel to climb out or kick
out. The wheel may either jump toward or away from the operator,
depending on direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory. Accessory
may kickback over your hand.
c) Do not position your body in the area where power tool will
move if kickback occurs. Kickback will propel the tool in direction
opposite to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw
blade. Such blades create frequent kickback and loss of control.
f) Do not “jam” the cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the possibility of
kickback or wheel breakage.
g) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel binding.
h) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully reenter the cut. The
wheel may bind, walk up or kickback if the power tool is restarted in the
workpiece.
i) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend to
sag under their own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of the workpiece on
both sides of the wheel.
j) Use extra caution when making a “pocket cut” into existing
walls or other blind areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that can cause kickback.
DESIGN AND APPLICATION AREA OF THE GROOVING TOOL:
The grooving tool is a handheld electric tool driven by means of a single-
phase electric motor of the brush type. The device is classified to the
second class of equipment (double insulation).
The tool is designed to cut grooves in walls for to lay cables and utility
conduits as well as to cut water drainage channels is metals or concrete.
The grooving operations are carried out with use of diamond blades,
without water spraying while the dust is collected by means of a vacuum
cleaner with the «M» dust protection class.
The tool can be provided with one or two diamond cutting blades.
This electric tool is designed for jobs with medium intensity. It is not
suitable for long-term operation under heavy duty conditions. Do never
use the tool for applications that need use of professional
equipment.
Each application of the tool not in line with the intended use as specified
below is strictly forbidden and makes the warranty terms null and void.
The manufacturer shall not be held responsible for possible
consequential damage that may arise due to or in connection with such
application.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
Application of the tool in accordance with the intended use also refers to
its maintenance, storage, transportation and repairs.
Defective electric tools can be handed over for repairs exclusively to
service workshops appointed by the tool manufacturer. The tools
supplied from electric grid shall be repaired exclusively by authorized
electricians.
Proper use cannot guarantee that no residual risk will occur. Due to the
design of the machine, the following risks may occur:
- Touching of the working accessory during its operation within the
unshielded area of the tool.
- Scalding while the working accessory is being replaced (During
cutting the working accessories are getting extremely hot. To avoid
scalding operators must wear protecting gloves to replace the cutting
Bekijk gratis de handleiding van Tryton TMB1500K, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tryton |
| Model | TMB1500K |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10327 MB |
