Tryton TMB1500K handleiding
Handleiding
Je bekijkt pagina 5 van 56
5
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use. Improper power tool maintenance is a reason for many
accidents.
f) Cutting tools should be sharp and clean. Keeping sharp cutting
edges in good condition reduces the risk of jamming and facilitates
operation.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account
operating conditions and the work to be done. Misusing a
power tool can result in dangerous situations.
h) At low temperatures and after a long brakes in operation it is
recommended to turn the power tool to operate it with no
load for a few minutes to provide proper grease distribution
inside its driving mechanism.
i) Use soft, damp (cannot be wet) cloth and soap to clean power
tools. Do not use petrol, solvents and other agents that may
damage your equipment.
j) Power tools can be stored/carried after making sure that all
moving components are locked and protected against
release with original devices intended for this purpose.
k) Store power tools in a dry, dust and water-protected place.
l) Carry your power tool in its original packaging to provide
protection against mechanical damage.
m) Keep handles and grip surfaces clean and free from oil and
grease. Secure grip and control over the tool in unexpected
circumstances are impossible if handles and grip surfaces are slippery.
WARNING! General warnings regarding the use of
power tools.
Repair:
a) Warranty and post-warranty repairs of its power tools are
carried out by PROFIX Service, which guarantees the best
quality or repair and use of genuine spare parts.
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.
WARNING! GROOVING MACHINE, work safety
warnings for use of the tool:
a) The shield must be firmly fixed to the electric tool and the
shield position must guarantee the maximum possible
safety for the operator, i.e. the cutting blade must be
covered to the maximum possible extent. The shield is meant to
protect operators against chips of materials that may be thrown out of
the groove and against accidental contacts with the cutting blade.
b) Only diamond cutting blades can be used. Do never use
accessories that are not designed, dedicated and recommended by the
tool manufacturer specifically for the specific tool. Although attaching
third-party accessories to the tool may prove possible it never
guarantees safe operation or maintenance.
c) The rated rotation speed of the applied working accessory
must be at least equal to the maximum possible rpm of the
tool. The maximum allowed rpm specified for the working
accessory may never be less than the maximum rpm
specified for the tool. When a working accessory rotates at a speed
exceeding maximum permitted limit it may break or crack and its part
be thrown away.
d) Diamond cutting blades can be applied only for jobs
according to the intended use. For instance it is forbidden to
use lateral surfaces of cutting blades for grinding or
polishing. Cutting blades are designed to remove materials with use
of the blade front edge. Any impact of side forces may lead to fracture of
such a machining accessory.
e) Cutting blades must be always assembled with use of
appropriate fixing flanges with right size. Adequate flanges
correctly support the cutting blade and minimize hazard of the blade
fracture.
f) Outer diameter and width/thickness of working accessory
must always fit within the range allowed for the specific
electric tool. Working accessories may prove insufficiently shielded
or uncontrollable.
g) Cutting blades, washers, flanges and other accessories must
perfectly fit the electric tool spindle. Working accessories that
are not commeasurable with the electric tool spindle may rotate with
play, produce excessive vibrations or lead to uncontrolled operation of
the tool.
h) Under no circumstances damaged or defective tools working
accessories can be used. Prior to each use operators are
obliged to inspect working accessories for possible spalls or
fractures. When the electric tool or its accessories are
dropped from a height it is mandatory to check whether it is
not damaged or use another accessory, for sure free of
defects. After having the tool checked install the working
accessory, switch the tool on and let it rotate for about one
minute at the highest rotation speed. Remember to make
sure that both the operator and third persons are outside
the hazardous area of the rotating tool. Damaged accessories
usually fall apart or reveal failures during such a test.
I) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations . The dust mask
or respirator must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise may cause
hearing loss.
j) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate area of
operation.
k) Hold power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power tool "live"
Bekijk gratis de handleiding van Tryton TMB1500K, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tryton |
| Model | TMB1500K |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10327 MB |
