Tryton TJV20 handleiding
Handleiding
Je bekijkt pagina 6 van 56
6
Using the charger:
a) Use only dedicated power adapters to charge the battery.
Application of a power adapter dedicated to charge another type of the
Battery indicator to show the battery status of charge*
battery unit poses a risk of fires.
Fig.F
b) The supplied charger should only be used for charging
Fig.G
batteries that are supplied together with it. Charging other
batteries may cause breaking and disintegration of the battery, bodily
harm, or fire.
c) Do not disassemble the charger.
d) The charger is designed exclusively for indoor use. It must not
be exposed to water or moisture.
e) Charge only in an ambient temperature between 15-25
degrees.
f) Do not insert metal objects of any kind into the charger.
The cordless hammer drill driver can be used to drill, hammer drill, and
drive screws.
The cordless hammer drill driver is designed exclusively for DIY
applications.
device
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
n
during the whole work time.
ź Сordless hammer drill driver -
One must implement additional safety measures to protect the operators
Operating instruction-
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
n
The declared total vibrations and declared noise emissions were
Fig.A 1. Keyless chuck
measured in accordance with a standard test method and may be used
2. Clutch control knob
for tool comparison.
3. Mode knob
The declared total vibrations and noise emissions can be used in
4. Gear shifter
preliminary exposure assessment.
5. Rotation direction switch
Warnings:
6. Fastener to hang on the belt
The vibrations and noise emissions during the actual use of the power
7.
tool may differ from the declared values depending on how the tool is
8. Battery*
used and on the type of the workpiece in particular.
9. Battery lock clip*
Determine safeguards to protect the operator. They should be based on
10. On/off switch
the estimated exposure under actual operational conditions (taking into
11. Auxiliary lighting
account all parts of the operating cycle such as when the tool is switched
Fig.C
off or idle except the start time).
APPLICATIONS AND CONSTRUCTION:
Despite using the tool according to its intended application it is
impossible to eliminate certain residual risk factors. Considering the tool
construction the following risks may occur when operating the tool:
- Touching the rotating drill bit with the hand operator's clothes.
- Burns when changing drill bits (Drill bits heat up intensely during
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
The set includes:
Device components (see page 2):
Battery level indicator button*
TECHNICAL PARAMETERS:
The tool must not be used for work requiring a
professional tool.
Any use of the that is not in observance with the above-
mentioned purpose is forbidden, leads to the loss of warranty, and
relieves the manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
or
1pc.
ź 1pc.
ź Warranty card - 1 pc.
13. Adapter*
14.
15.
16. Clutch setting and mode mark
17. Left-threaded fixing screw
* The accessories shown or described are not standard equipment.
For the complete offer of auxiliary equipment, see our catalogue.
Strap for hanging on hand
12. Charger*
Rotation speed under no-load conditions ( Gear I/II)
Supply voltage
Chuck clamping range
Gear shifter I-II
Maximum torque
Maximum drilling
diameter
Wood
Steel
Acoustic pressure level(LpA)
Acoustic power (LwA)
Vibration level according to EN 62841-1,
hammer drilling a
h,ID
Weight (with battery)
(t K=1,5 m/s²)olerance of measurements
Recommended 20 V Li-ion batteries: TJ15AK (1,5Ah), TJ2AK (2Ah), TJ4AK (4Ah)
Recommend chargers: TJ3LD(3-5h), TJ1LD (1h)
n =0-400 /0-1500 /min
o
20 V d.c.
yes
2
14,265 m/s
99,9 dB(A)
89,9 dB(A)
1,75 kg
13 mm
25 mm
ø 0,8-13 mm
44 Nm
Сoncrete
10 mm
Tolerance of measurements K ,K
LpA LwA
3 dB(A)
Vibration level according to
drilling
EN 62841-1,
a
h,D
( K=1,5 m/s²)tolerance of measurements
2
1,746 m/s
Bekijk gratis de handleiding van Tryton TJV20, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tryton |
| Model | TJV20 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11694 MB |
