Tryton TJV10 handleiding
Handleiding
Je bekijkt pagina 7 van 56
7
and three LEDs mean full battery.
n Choosing torque (Fig. F)
The driver is equipped with a ring (2), which can be used for setting the
toque when driving screws. The ring has 22 settings, from 1 to 21, and a
drilling setting.
Press the battery lock button (8) and take the battery (7) out of the drill
driver
Using a given setting (from 1 - 21) means that the clutch is set to an assigned
toque. This makes it possible to prevent a screw from being driven too far or
Connect the battery (7) to the charger (11) (see Fig. C).
being damaged. Different torques should be used for different screws and
Connect the adapter plug (12) to the charger (11).
materials.
4. Connect the adapter to a mains socket (110–240 V, 50-60 Hz).
Always start with a low torque and increase gradually until the desired
result is achieved.
For drilling in metal, wood or plastic, set the ring (2), so that the indicator
Press the battery lock button (8) and take the battery (7) out of the drill
(15) points to symbol (16).
driver
Connect the battery (7) to the charger (11) (see Fig.
n Shifting gear (Fig. A)
The gear shifter (3) makes it possible to choose 2 rotation speed ranges.
Gear I: Used for driving and unscrewing screws.
Gear II: Used for drilling.
CAUTION: Do not change the position of the gear shifter (3) during tool
operation as this may damage the gear box. Always allow the tool to come to a
full stop before changing the setting of the gear shifter.
If the gear shifter does not move all the way, move the drive spindle slightly.
n Changing the chuck (Fig. G)
1. Disconnect the battery (7) from the driver.
2. Open the chuck as much as possible (1)
3. Using a PH 2 (Philips No.2) screwdriver, rotate the fixing screw of the
chuck clockwise (CAUTION! Left-thread). To free a seized bolt hit is
n Battery charging indicator
gently on its head.
A green LED light indicates that the charger is connected to a power source.
4. Unscrew the chuck of the drill/screwdriver counter-clockwise (looking
After the battery is connected, the red LED is on to indicate charging.
from the point of view of the chuck).
Blinking green battery LEDs also indicate that the battery is charging and
CAUTION: A jammed keyless chuck (1) can be released by inserting the
show the current battery level.
short end of a hex key in the chuck and lightly tapping the longer arm of the
When the battery is fully charged, the red LED goes off and the green LED is
key (see Fig.D).
on.
5. To attach the chuck, screw it onto the drive spindle clockwise and secure
After charging, disconnect the charger and remove the battery.
by screwing in the fixing screw counter-clockwise using a PH 2
NOTE! The battery may get slightly hot when charging. This is not a
screwdriver (No.2 Philips).
malfunction.
AUXILIARY COMPONENTS:
The lithium-ion battery can be charged at any moment, without detriment
to its life. Interrupting the charging process does not entail a risk of
ź The practical fastener (5) can be used for attaching the drill-driver on the
damaging the battery cells.
user's belt, both for right-hand and left-hand dominant users.
ź The drill/driver is equipped with an auxiliary light (10) for the area of
IN USE:
drilling/driving, which turns on after the appropriate switch (9) is
n Turning on/off
pushed.
The switch (9) has fluid rotation speed adjustment built-in.
n Installation and removing drills to/from the keyless chuck
Press the switch to activate the power tool. The rotation speed will increase
CAUTION: Disconnect the battery from the driver or put the rotation direction
the further the switch is pushed. To stop the power tool, release the switch.
switch (4) in the middle position to secure the machine from being started by
n Choosing rotation direction (see Fig. E)
mistake, which could in turn cause harm to the user.
The driver can work with clockwise (right) or counter-clockwise (left)
When the tool trigger (9) is released the drill chuck is locked. It enables
rotation.
quick, easy and convenient replacement of a working tool installed in the
- to select clockwise rotation, move the clockwise/counter-clockwise slider
drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate the
(4) to the left (looking from the back of the driver),
chuck ring anticlockwise to expand the opening of the chuck. Insert a new
- to select counter-clockwise rotation, move the clockwise/counter-
drill (or a working bit) into the chuck and rotate the chuck ring clockwise to
clockwise slider (4) to the right (looking from the back of the driver),
secure the drill in the drill chuck.
When the rotation direction switch is in the middle position, the
Drills (or other working bits) must be moved to the full depth of the chuck
is locked.
opening.
For drilling and driving screws in, clockwise operation should be selected. For
n Drilling boreholes
taking out the drill bit, removing a stuck drill bit, or unscrewing screws,
counter-clockwise operation should be selected.
1. To drill deep boreholes carry out your job gradually, drill to lower
Charge the battery fully before use.
TJ3LD
The first charging procedure using TJ3LD should last at least 5 hours.
1.
(see Fig. B).
2.
3.
TJ1LD
The first charging procedure using TJ1LD should last at least 1 hour.
1.
(see Fig. B).
2. H).
3. Connect the charger plug to a mains socket (220–240 V, 50 Hz).
On/off
switch(9)
Charger
Charger
7
11
H
Bekijk gratis de handleiding van Tryton TJV10, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tryton |
| Model | TJV10 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11458 MB |
