Handleiding
Je bekijkt pagina 7 van 18
-6-
IV. e - LOADING THE UNIT (cont’d)
NOTE: BOTTOM SHELF SHOULD ALWAYS BE
PRESENT DURING OPERATION TO MAINTAIN PROPER
AIR CIRCULATION. FOOD SHOULD NOT BE LOADED
DIRECTLY ON THE BASE OF THE CABINET. DOING SO
MAY VOID THE WARRANTY OF THE CABINET.
V. CARE & MAINTENANCE
DISCONNECT ELECTRICAL POWER SUPPLY
BEFORE CLEANING ANY PARTS OF THE UNIT.
V. a - CLEANING THE CONDENSER
The most important thing you can do to ensure a long, reliable
service life for your Centerline is to regularly clean the condenser
coil.
The condensing unit requires regularly scheduled cleaning to
keep the nned condenser clean of lint and dust accumulation.
Keeping the condenser clean allows the cabinet to operate
more efciently and use less energy. To clean the condenser,
rst disconnect electrical power to the cabinet.
Next, remove the front lower louver panel by removing the single
screw from inside the door opening and gently pulling it towards
front (refer to previous gures 4 and 5).
NOTE: DOOR SWITCH WIRING MAY BE PRESENT AND
ATTACHED TO THE LOUVER.
Vacuum or brush any dirt, lint or dust from the nned condenser
coil, the compressor and other cooling system parts. If
signicant dirt is clogging the condenser ns, use compressed
air to blow this clear. Care should be taken not to bend any of the
condenser ns, as this will reduce performance and compressor
life. Reverse the process to install louver assembly back in place.
V. b - HINGE REPLACEMENT
To replace the hinge, the upper and lower panels need to
be removed from the face of the unit. The hinges can be
removed as described in section III.f for door installation.
Refer to section III.f for instructions to remove, install, and
adjust torque on doors when replacing a hinge. Please
refer service manual or contact service support for detailed
instructions on hinge replacement
V. c - REPLACING THE GASKETS
To replace the gasket, grasp it rmly by one corner and pull
it out. Before attempting to install a new gasket, both the unit
and gasket must be at room temperature. Insert the four
corners rst by using a rubber mallet (or hammer with a block
of wood). After the corners are properly inserted, work your
way towards the center from both ends by gently hitting with
a mallet until the gasket is completely seated in place (see
gure 13 for proper gasket placement).
V. d - CLEANING THE EXTERIOR
Exterior anodized aluminum should be cleaned with warm
water, mild soap and a soft cloth. Apply with a dampened
cloth and wipe in the direction of the metal grain.
Avoid the use of strong detergents and gritty, abrasive
cleaners as they may tend to mar and scratch the surface.
Do NOT use cleaners containing chlorine, this may promote
corrosion of the stainless-steel door.
Care should also be taken to avoid splashing the unit with
water, containing chlorinated cleansers, when mopping the
oor around the unit.
For stubborn odor spills, use baking soda and water (mixed
to a 1 TBSP baking soda to 1-pint water ratio).
V. e - CLEANING THE INTERIOR
For cleaning the interior, use baking soda with warm water,
and a soft cloth. Apply with a dampened cloth and wipe in
the direction of the metal grain Use on breaker strips as well
as door and drawer gaskets.
Remove single screw (seen
in gure 4 and 5) and pull
lower panel off to clean the
condenser coil.
Fig. 12
Inside Door
Fig. 13
Retainer Gasket
Outside Door
Foam
Stainless Steel Door Shown
V. CARE AND MAINTENANCE (continued)
Bottom shelf
Fig. 11
IV. OPERATION (continued)
Bekijk gratis de handleiding van Traulsen CLBM-23F, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Traulsen |
| Model | CLBM-23F |
| Categorie | Vriezer |
| Taal | Nederlands |
| Grootte | 3673 MB |
