Handleiding
Je bekijkt pagina 5 van 18
-4-
III. f - REMOVING DOORS & HARDWARE (cont’d)
To remove the door, two bolts on the bottom hinge brackets
need to be removed. Then remove two bolts on the top hinge
bracket. The door can then be lifted from the unit.
Note that hinge brackets are under spring tension. Carefully
move the door just far enough to allow the bracket to unwind.
First, ensure the door weight
opposite the hinge side is
supported. The top hinge
bracket bolts can be removed.
Fig. 7
To re-install the door, top and/or bottom louvers, and hinges,
please reverse the appropriate sections of the preceding
procedure.
III. g - DOOR REMOVAL FOR HALF DOOR UNITS
To begin, remove top/bottom panels, then open the door to
its open feature position about 110°. For top door, remove
two bolts on the top hinge bracket. The door can then be
lifted up from the center hinge hardware. The plastic bushing
will remain in the top door.
For bottom door: support the bottom door weight opposite
the hinge side so minimum movement occurs when the bolts
from the lower hinge plate are removed. Remove two bolts
on the bottom hinge bracket. The door can then be moved
down from the center hinge hardware. The plastic bushing
will remain in the bottom door. Once top/bottom doors
removed, two screws can then be removed on the center
hinge.
Note that hinge brackets are under spring tension. Carefully
move the door just far enough to allow the bracket to unwind.
III. h - CORD & PLUG
All Centerline reach-in models are supplied with a cord &
plug attached. It is shipped coiled and secured by a nylon
strip to the back of the cabinet near condensing unit area.
For your safety and protection, all units supplied with a cord
and plug include a special three-prong grounding plug on
the service cord. Select only a dedicated electrical outlet
with grounding plug for power source.
NOTE: DO NOT UNDER ANY CIRCUMSTANCES CUT OR
REMOVE THE ROUND GROUNDING PRONG FROM THE
PLUG OR USE AN EXTENSION CORD.
III. i - POWER SUPPLY
The supply voltage should be checked prior to connection
to be certain that proper voltage for the cabinet wiring
is available (refer to the serial tag to determine correct
unit voltage). Make connections in accordance with local
electrical codes. Use qualied electricians.
Use of a separate, dedicated circuit is required. Size wiring
to handle indicated load and provide necessary over current
protector in circuit (see amperage requirements on the unit’s
serial tag).
III. j - WIRING DIAGRAM
Refer to the wiring diagram located on the exterior back
of the cabinet for any service work performed on the unit.
Should you require one, please contact Traulsen Service at
(800) 825-8220, and provide the model and serial number
of the unit involved.
III. k - INSTALLING OPTIONAL INTERIOR KITS
In addition to their standard interiors, Centerline models
also offer the option for additional shelves or tray slides.
If ordered, these are shipped as kits along with the unit,
packaged in a separate cardboard box which contains all
the necessary parts and hardware for on-site installation.
To install additional shelves, install the included pins on the
pre-cut holes where required. Secure the shelves to the pins
using nylon tie-wraps.
Installation of optional tray slides varies with each cabinet,
and with each type of tray slide ordered. To install optional
tray slides, follow the directions packaged inside the kit
carton.
Half door: Lift top and bottom
doors about center hinge
Fig. 8
Plastic
Pushings
III. INSTALLATION (continued)
Bekijk gratis de handleiding van Traulsen CLBM-23F, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Traulsen |
| Model | CLBM-23F |
| Categorie | Vriezer |
| Taal | Nederlands |
| Grootte | 3673 MB |
