Tornado VCRMCWC handleiding
Handleiding
Je bekijkt pagina 20 van 115
English 20
Indicator light Voice prompt Solution
Robot -
Flashing Red
Error F7: Laser distance sensor fault.
Please check and try to restart the
system.
Please check whether the laser distance sensor are
entangled with dirt. Please clean it, and then try to turn off
and then turn on the system.
If the fault persists, please contact our customer service.
Error F8: Water pump malfunction. Try
to restart the system.
Clean the water tank, water pump interfaces of water tank
and Robot, and Robot base drain; check the mopping
combo module. Then, try to shut off for restart up.
If the fault persists, please contact the sales service.
Charging base
- Solid Red
Please check whether the dust bag is
installed and close the cover properly.
- Please check whether the dust bag is missing, ensure
that the dust bag is installed in place, and close the dust
bag cover.
Charging base -
Flashing Red
Long time using dust bag, please
replace the dust bag.
- Please check the status of the dust bag and replace the
dust bag in time. If the dust bag is new, please take out the
dust bag and reinstall.
Air duct blocked. Please clean it.
Please check whether the auto-empty dirt port of the robot
and the auto-empty dirt port of the charging base are
blocked.
If the above cannot be solved, refer to the chapter «Clean
the air duct» to clean the air duct.
If the fault cannot be eliminated according to the above, please contact our customer service. The problems you encounter
are also what we are concerned about and hope to help you solve.
FAQs
Problem type Solution
Unable to turn on.
Insufficient power. Please make sure that the charging base has been connected to the
power supply, and then place the robot on the charging base and align with the charging
contacts, and the device will automatically start up.
If it still cannot be started, please try to restart the system. When it is not charging, press
Power button for 10 seconds to force the shutdown, and then press Power button for 3
seconds to start the system.
Unable to charge.
Please remove the device and check whether the indicator light of the charging base is
on.If not, please make sure that the power cable and charging base’s power port have been
connected tightly, and the plug and the power socket have been plugged in. (If the light does
not on, please contact customer service)
If the indicator light of the charging base is on, connect the powered robot to the charging
base, and ensure that the charging contact pins of the robot is aligned with the charging
contacts of the charging base. Check if the indicator light of the robot changes to the
breathing state.
If the indicator light of the charging base is on and the robot is turned on, but the robot
cannot be charged, please try to turn off the robot and pull out the charging base, wipe the
charging contact pins of the robot and the charging contacts of the charging base with a soft
dry cloth, and then try the above two steps again. (If the problem still exists, please contact
the customer service)
Unable to start.
Make sure that the robot is connected to the power supply.
Make sure the robot is fully charged.
Press and hold Power button for 3 seconds to turn on the robot.
Unable to recharge.
Please clear the obstacles near the chargingbase and put the charging base in an open
area. Please ensure that no objects are placed within
1.5m in front of the charging base and 0.5m on both sides.
Please use a soft dry cloth to wipe the infrared obstacle avoidance sensor, the recharge
sensor, the charging base location beacon, the charging contact pins and charging contacts.
Please put the robot near the charging base.
Stop working suddenly.
Check whether the robot is trapped or stuck by foreign matters.
Check whether the battery power is too low.
Check whether there is a red light or fault indication on the robot. Please refer to the chapter
«Troubleshooting».
If the problem still can be resolved, please restart the system, long press Power button for 10
seconds to force the shutdown, and then press Power button for 3 seconds for starting up.
Bekijk gratis de handleiding van Tornado VCRMCWC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tornado |
| Model | VCRMCWC |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 17004 MB |
