Topex 44E117 handleiding
Handleiding
Je bekijkt pagina 5 van 24
5TOPEX.PL
after the torch is switched o.
3. Do not put hot torch burner close to ammable
materials.
4. Before storing ensure that gas valve wheel is turned
o, hot torch must cool down.
5. Do not store the gas container in temperature
above 40°C (104ºF) or in direct sunlight.
6. Keep the torch beyond reach of children.
7. With this torch use propane, butane or propane and
butane mixed.
8. Protect the torch and rubber hose against oil, acids
and other chemical agents.
9. When operating the torch always use personal
protection measures: protective glasses and gloves.
10. Do not operate damaged torch or a torch with
damaged rubber hose.
11. Do not repair the torch by yourself, do not dismantle
parts of the torch.
12. Use the torch accordingly to the manual.
13. To safety work with the burner the reductor is no
necessary.
WARNING!
– Do not use brazed joints for elements that may be
subject to temperature above 130°C.
– Do not join parts used for lifting weights with brazed
joints.
CAUTION!
Ensure that exible, rubber hose between
torch and gas container is in good technical
condition, connection is air-tight, and gas pressure does
not exceed the value on the rubber hose.
CAUTION!
Rubber hoses are equipped with left hand
thread connectors.
CAUTION!
Use pressure reducing valve to minimize gas
pressure impact onto ame stability.
CAUTION!
All checks and repairs should be carried out by
the supplier’s service department or by service
site certied by the supplier. All checks and repairs must
be carried out only when rubber hose is disconnected
from the gas cylinder. Cut o gas supply before
disconnecting the hose!
CAUTION!
Do not pull the rubber hose to move or lift gas
container.
Check condition of rubber hose each time before
starting work. In case any damage is found (accidental
surface cut, signs of burns, bulge or change of diameter)
immediately replace the hose with a new one.
Rubber hose also must be replaced not later than 5
years from its production date specied on the hose.
1 2 3 4
1. Read the manual, observe the warnings and safety
conditions contained in it!
2. Outdoor tool.
3. Attention! Hot surfaces.
4. Keep children away from the tool.
TECHNICAL PARAMETERS
Flame temperature [°C] 1850
Gas consumption [g/h] max 2000
Burner power [kW] max 28
Number of burners 7
Burner diameter (mm)
W
1
=9; 12,5, W
2
=13; 14, W
3
=25,
W
4
=45, W
5
=22; 32; 47, W
6
=32;
42; 58
Type of burner
2 pin point + 1 pipe + 1 at +
3 broad ame + brazing torch
Hose length 3m
Additional equipment pressure reducing valve
TORCH COMPONENTS
a. Burner
b. Handle
c. Gas valve wheel
d. Rubber hose
e. Keys
f. Gas valve lever
g. Pressure reducing valve
h. Soldering torch
i. Stand
j. Sti connection
OPERATION AND USE
Starting up the torch
– Release the gas valve lever (except for soldering tip)
– Turn gas valve of the torch towards (-) to turn it o.
– Connect pressure reducing valve to gas container
– Connect gas hose to the torch and pressure reducing
valve.
– Open gas container valve to supply pressure reducing
valve with gas.
– Open pressure reducing valve.
– Direct the torch forward.
– Press the gas valve lever against the handle (except
for soldering tip)
Bekijk gratis de handleiding van Topex 44E117, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Topex |
| Model | 44E117 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3537 MB |
