Toa BS-680U handleiding

4 pagina's
PDF beschikbaar

Handleiding

Je bekijkt pagina 3 van 4
Step 3. Perform wiring.
3-1. Connectboththelead-inandlead-outcablestothepush-inconnectorattachedtothecabinet.
[Applicable cable]
•Solidcopperwire: ø0.8−2.0mm(AWG20−12)
•Strandedcopperwire:0.5−2.0mm
2
(AWG20−14)
Note: Donotsoldertheendofstrandedcable.
3-2. InsertthefastenterminalsttedwiththeHOT(black)cablefromtheinputconnectorandCOM(white)
cable from the capacitor into the taps of the transformer on the speaker unit.
ConnecttheCOMcabletothetransformer'sCOMtap,theHOTcabletothedesiredtransformer'sinput
tap.(Refertothegurebelow.)
The relationshipbetweenimpedanceandinputpowerisshownbelow.
Input Power 25VLine 70VLine
6 W 105Ω 830Ω
3 W 210Ω 1.67kΩ
1W 650Ω 5kΩ
From the amplifier
Cabinet
Input connector
COM (white)
HOT (black)
From
the amplifier
To the next
speaker
To the next speaker
Input connector
HOT
COM
9 mm (0.35")
650Ω
210Ω
105Ω
COM
5kΩ
1.67kΩ
830Ω
Matching transformer
(on the speaker unit)
ToconformwithUL1480UUMW/ULC-S541,requirementsforrealarm
signalingspeaker,eldwiresmustbeconnectedasshownabove.
And, installation must comply with all National and Local Building
Codes,alsoNFPAguidelinesorCAN/ULC-S524.
CAUTION
Step 4. Replacethebafetothecabinet,thentighten2screwslooselyattachedonbothsidesofthecabinet.
2-3. When mounting the cabinet into the wall:
(1) Make amounting hole of 260x175 mm
(10.24"x6.89")inthewall.
(2)
Cover2hangingholeswiththesupplied2
pieces of sponge tape.
Leavetheunusedholescoveredwithtape.
(3)Removethecabinet'sknockouthole,run
the cables through this hole, then install
the cabinet using 4 supplied screws
(tappingscrew4x16).
Fitthe supplied rubbergrommetintothe
knockout hole.
Note: Cut a hole in the grommet's thin
membrane to match the cable size.
Unit: mm (in)
Cabinet
Knockout hole:
ø20.5 (0.81)
Sides: 4 holes
Bottom: 2 holes
Wall
286 (11.26)
260±3
(10.24±0.12)
175±3
(6.89±0.12)
150
(5.91)
Speaker
cable
Tapping screw 4 x 16 (accessory)
Caution
Whenconnectingthespeakertotheamplier,
besuretomatchbothimpedanceandvoltage
line(25Vor70V)eachother.
Otherwise,thespeakerorampliermayfail.

Bekijk gratis de handleiding van Toa BS-680U, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

MerkToa
ModelBS-680U
CategorieSpeaker
TaalNederlands
Grootte660 MB