Handleiding
Je bekijkt pagina 35 van 80
INSTALLATIONCLEANING
IMPORTANT:
always disconnect the appliance from the gas
and electricity mains before carrying out any
cleaning operation.
2) HOT PLATE
It is very important to clean the surface soon after
every use, when the glass is still tepid.
Periodically wash the hot plate, the enamelled stell
pan support, the enamelled burner caps “A”, “B”
and “C” and the burner heads "T" (see fig. 6 - 6/A)
with lukewarm soapy water. They should also be
cleaned plugs "AC" and flame detection "TC" (see
fig. 6). Clean them gently with a small nylon brush
as shown (see fig. 6/B) and allow to dry fully.
Do not wash in the dishwasher.
Do not allow vinegar, coffee, milk, salted water,
lemon or tomato juice from remaining in contact
with the enamelled surfaces for long periods of
time.
Do not use metallic sponges, powder abrasives or
corrosive sprays.
WARNINGS:
comply with the following instructions, before
remounting the parts:
- check that burner heads slots (see fig. 6
-6/A) have not become clogged by
foreign bodies.
- Check that enamelled burner cap “A - B -
C” (fig. 6 - 6/A) have correctly positioned on
the burner head. It must be steady.
- For an exact stability of the pan supports,
verify that they are inserted in their specific
centering niches situated on flanges.
- Do not force the taps if they are difficult open
or close. Contact the technical assistance
service for repairs.
- Don’t use steam jets for the equipment
cleaning.
- Do not wash enamel parts in dishwasher. Put
them inside hot water for a while, clean with a
soft cleaner and dry with a soft cloth or towel.
TECHNICAL INFORMATION
FOR THE INSTALLER
Installation, adjustments of controls and
maintenance must only be carried out by a
qualified engineer.
The appliance must be correctly installed in
conformity with current law and the
manufacturer's instructions.
Incorrect installation may cause damage to
persons, animals or property for which the
Manufacturer shall not be considered
responsible.
During the life of the system, the automatic
safety or regulating devices on the appliance
may only be modified by the manufacturer or
by his duly authorized dealer.
3) INSTALLING THE HOT PLATE
Check that the appliance is in a good condition after
having removed the outer packaging and internal
wrappings from around the various loose parts. In
case of doubt, do not use the appliance and contact
qualified personnel.
Never leave the packaging materials (cardboard,
bags, polystyrene foam, nails, etc.) within
children’s reach since they could become
potential sources of danger.
The measurements of the opening made in the top of
the modular cabinet and into which the hot plate will be
installed are indicated in either fig. 7. Always comply
with the measurements given for the hole into which
the appliance will be recessed (see fig. 7 and 8)
.
The appliance belongs to class 3 and is
therefore subject to all the provisions
established by the provisions governing such
appliances.
Note: continuous use could cause the burners to
change colour due to the high temperature.
31
Bekijk gratis de handleiding van Teka GBC 32000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Teka |
| Model | GBC 32000 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 10264 MB |
Caratteristiche Prodotto
| Apparaatplaatsing | Ingebouwd |
| Soort bediening | Draaiknop |
| Kleur van het product | Zwart |
| Ingebouwd display | Nee |
| Breedte | 300 mm |
