TC Electronic MD4 HD handleiding
Handleiding
Je bekijkt pagina 6 van 22
6 MD4 HD NATIVE User Manual
4. Connection and Setup
4.1 Inserting the MD4 HD NATIVE plug-in in
your DAW project
Once you have downloaded the plug-in, you can now apply it to a channel in your
DAW to begin using the eect. This process may vary slightly depending on your
software, but generally should require these steps:
• Select a channel or bus in your DAW to which you would like to add the eect.
Access the mixer page where you should see a section dedicated to eect slots.
• Open the menu where you can select from a list of eect types, which
probably includes many stock plug-ins that are included with the DAW.
There should be submenu to view general VST/AU/AAX options.
• The plug-in will likely be found in a dedicated TC Electronic folder. Select the
MD4 HD NATIVE and it will now be added to the signal chain.
Double click on the eect slot that contains MD4 HD NATIVE to view the plug-in
UI.
4.2 Operating the MD4 HD NATIVE
After you have installed the plug-in, and activated the iLok license, you can begin
working with the plug-in on your tracks.
Adjustments to the eect are done using the plug-in user interface:
Most DAWs oer the ability to move or drag plug-ins from one track/bus to
another, and MD4 HD NATIVE supports this as well.
Most DAWs also feature an on/o switch for plug-ins, accessible inside the plug-in
window and/or the track itself. Note that some hosts don’t oer smooth on/o
switching. Use the Global Bypass button on the MD4 HD plug-in interface for a
smooth and latency-compensated bypass.
4.2.1 Insert vs Aux Eect
The MD4 HD NATIVE is intended for insertion directly into an eect slot on a single
channel, sub mix bus or master bus, which passes the entire signal through the
eect.
Be careful if using MD4 HD NATIVE on an auxiliary bus, as mixing the output of
MD4 HD NATIVE with the original track sound will potentially create a phasing
issue depending on your DAW's ability to correctly compensate for latency in
plug-ins.
4.2.2 Mono/Stereo Operation
The MD4 HD NATIVE can be used both as a mono instance on mono tracks and a
stereo instance on stereo tracks.
In the case of a mono out instance, the output signal is made by outputting the
left plug-in channel only. In this case, panning should not be used.
4.2.3 Bypass
Press the BYPASS button at the top to bypass or engage the MD4 HD NATIVE.
4.2.4 Automation
Please be aware that automation of certain parameters, can cause audible
artifacts.
In case you need to automate these parameters, you should take care that
changes only take place in parts where no audio is sent to the plug-in.
4.2.5 Parameter Overview
The MD4 HD NATIVE is a 5-band, 2-Channel Dynamics processing algorithm. The
algorithm contains:
• • Stereo 6-band precision EQ (linked, left/right, or mid/side operation)
• • Stereo 5-band compressor (stereo or mid/side operation)
• • The MD4 HD NATIVE will run at sample rates up to 192kHz
4.3 Signal ow through the algorithm:
NORMALIZER
GAIN
MS ENCODER
TRIM GAIN
LOW CUT
EQ (6 BAND)
5-BAND DYNAMICS
(COMPRESSOR
WITH DEFEAT)
MS DECODER
LIMITER GAIN
SOFT CLIPPER
LIMITER
OUTPUT GAIN
(+ COMPARE GAIN)
Bekijk gratis de handleiding van TC Electronic MD4 HD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | TC Electronic |
| Model | MD4 HD |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8045 MB |
