Stiga SBC 627 KD handleiding

Handleiding

123456789101112131415161718192021222324252627282930/ 30

Afdrukken

Je bekijkt pagina 18 van 30

6

ting devices or ones homologated by the

Manufacturer.

1.3.1 Selecting the cutting device

Choose the most suitable cutting device for the

job to be done, according to these general indi-

cations:

– the 3-point blade is suitable for cutting brush-

wood and small shrubs up to 2 cm in diameter;

– the 4-point blade is suitable for cutting tough

grass over large surfaces;

– the cutting line head can eliminate tall grass

and non-woody vegetation near fences, walls,

foundations, pavements, around trees, etc. or

completely clean a particular area of the gar-

den;

– the saw blade (if permitted) allows small

woody parts to be cut and small trees to be

felled.

Every cutting device must be tted with a specif-

ic guard, as indicated by the following directions.

IMPORTANT The cutting devices are fastened

with a left-hand thread and therefore must be un-

screwed clockwise and screwed on anticlock-

wise. Remove  all  elements that may  have  been 

assembled, which will be used in various con-

figurations, according to the cutting device used.

1.3.2 3 or 4-point blade “Tri-Arc” blade”

(Fig. 6)

a) Assembly

– Fit the inner ring-nut (1) in the indicated di-

rection, making sure that the inner ring-nut’s

grooves match perfectly with those of the an-

gle transmission (2).

– Fit the blade (3) and the outer ring-nut (4), with

the at part toward the blade.

– Insert the supplied wrench (5) in the specic

hole, then turn the blade (3) by hand and push

the wrench (5) until it enters the hole of the an-

gle transmission (2), blocking rotation.

– Fit the cup (6) fully tightening the nut (7) anti-

clockwise (25 Nm).

– Remove the wrench (5) to restore rotation.

b) Adjusting the guard

– Remove the additional guard (8 - if already t-

ted), unhooking hooks clicked into the guard

(9).

c) Disassembly

– Insert the supplied wrench (5) in the specic

hole, then turn the blade (3) by hand and push

the wrench (5) until it enters the hole of the an-

gle transmission (2), blocking rotation.

– Unscrew the nut (7) clockwise and remove

the cup (6).

– Pull out the outer ring-nut (4), then remove the

blade (3) and the inner ring-nut.

1.3.3 Cutting line head (Fig. 7)

a) Assembly

– Fit the inner ring-nut (1) in the indicated di-

rection, making sure that the inner ring-nut’s

grooves match perfectly with those of the an-

gle transmission (2).

– Insert the supplied wrench (3) in the specif-

ic hole of the inner ring-nut (1), then turn the

ring-nut by hand and push the wrench (3) until

it enters the hole of the angle transmission (2),

blocking rotation.

– Fit the cutting line head (4) screwing it anti-

clockwise.

– Remove the wrench (3) to restore rotation.

b) Adjusting the guard

– Fit the additional guard (8), inserting the cou-

plers into the respective seats in the guard (9)

and pressing until a click is heard.

WARNING! When using the cutting line

head, the additional guard, with line cutting

knife, must always be fitted.

c) Disassembly

- Insert the supplied wrench (3) in the specic

hole of the inner ring-nut, then turn the ring-nut

by hand and push the wrench (3) until it enters

the hole of the angle transmission (2), block-

ing rotation.

– Remove the cutting line head (4) unscrewing

it clockwise.

1.3.4 Saw blade (if permitted) (Fig. 8)

a) Assembly

– Fit the inner ring-nut (1) in the indicated direc-

tion, making sure that the grooves match per-

fectly with those of the angle transmission (2).

– Fit the blade (3) and the outer ring-nut (4), with

the at part toward the blade.

– Insert the supplied wrench (5) in the specic

hole, then turn the blade (3) by hand and push

the wrench (5) until it enters the hole of the an-

gle transmission (2), blocking rotation.

– Fit the cup (6) fully tightening the nut (7) anti-

clockwise (25 Nm).

– Remove the wrench (5) to restore rotation.

b) Adjusting the guard

– Remove the guards that may have been used

123456789101112131415161718192021222324252627282930/ 30

Bekijk gratis de handleiding van Stiga SBC 627 KD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Stiga (Niet gecategoriseerd)

Handleiding bekijken

Stiga Park 100 Combi EL

Niet gecategoriseerd - handleiding

Handleiding bekijken

Stiga SBC 645 KD

Niet gecategoriseerd - handleiding

Handleiding bekijken

Stiga SBC 635 KD

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd