Stamos S-MTM 220 handleiding
Handleiding
Je bekijkt pagina 12 van 43
22 23
Rev. 06.05.2022 Rev. 06.05.2022
14. Use only supplied Torch on this Inverter Air Plasma Cutter. Using components
from other systems may cause personal injury and damage components within.
15. People with pacemakers should consult their physician(s) before using this pro-
duct. Electromagnetic elds in close proximity to a heart pacemaker could cause
interference to, or failure of the pacemaker.
16. USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition. When using an extension cord, be sure to sue one heavy enough to
carry the current your product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. A 50 foot extension cord
must be at least 12 gauges in diameter, and a 100 foot extension cord must be at
least 10 gauges in diameter. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
CHECKING PACKAGING UPON CONSIGNMENT
When you received the goods proceed with opening the packaging if there are no
signs of damage. If there are signs of damage on packaging please send a detailed list
and report of all damage to the goods to your local representative within 3 days after
delivering.
Disposing of packaging
The various items used for packaging (cardboard, plastic straps, polyurethane foam)
should be conserved, so that the device can be sent back to the service centre in best
conditions in case of problem.
SETTING THE DEVICE
Setting the welder must be carried out in accordance with the following rules:
• The operator must have free access to the device as well as its connections and
controls.
• It is forbidden to set the device in small rooms. It is important that the room
must be equipped with good ventilation system, it should be clean and without
dust.
• The device with wiring can not be obstacle on the passage and can not reduce
the work area of other workers.
• The device can be placed only on a at surface. The gas cylinders must be pro-
perly protected.
SUPPLIED EQUIPMENT:
Cable with mass clamp.
MMA welding cable with electrode holder.
TIG welding cable WP-26 along with accessories:
Collets: 1.6 mm / 2.4 mm / 3.2 mm.
Ceramic nozzles no 5, 6, 7.
Long cap.
Tungsten.
MIG welding cable MB15AK along with contact tips 0.8 mm and 0.9 mm.
Gas hose.
Mask.
Hammer.
Brush.
EN
RoHS
CERTIFICATES –welder has been manufactured in accordance
with CE and RoHS certicates. It guarantees long life time and
high quality of the device.
MOSFeT
The welder uses MOSFET technology. This technology (as no
other) ensures the highest efciency. In comparison to the cur-
rent consumption amount we gather over-proportional power
amount. This results in the efciency of 93%! Welding current
is very stable and it ensures perfect fusion weld. Thanks to the
MOSFET technology, the machine is light and compact.
1 PH
GAS
Standard supply voltage = the welder is supplied by 230 V voltage
from the single-phase socket (230V +/- 10%).
INERT GAS = for WIG / TIG welding it is necessary to use inert
gas (e.g. argon).
FANS = very efcient fans ensure the optimal heat release during
the welder operation.
EN
INSTALLATION AND CONNECTION
User panel:
Bekijk gratis de handleiding van Stamos S-MTM 220, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Stamos |
| Model | S-MTM 220 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8386 MB |
