Stamos S-MIGMA 250.IGBT handleiding
Handleiding
Je bekijkt pagina 7 van 33
12 13
Rev. 23.05.2022 Rev. 23.05.2022
EN
• Chemical substances (lubricants, solvents) must be removed from the surfaces of welded objects as
they burn and emit toxic smokes under the inuence of temperature.
• The welding of galvanised objects is permitted only when efcient ventilation is provided with ltration
and access to fresh air. Zinc fumes are very toxic, an intoxication symptom is the so called zinc fever.
2. TECHNICAL DATA
Product name WELDING MACHINE
Model S-MIGMA 250.IGBT
Voltage / frequency 230V~ / 50 Hz
Rated input current [A] 33 (MMA)
22.5 (TIG)
29.5 (MIG)
No-load voltage [V] 62 (MMA / TIG / MIG)
MMA welding current [A] 15-250
TIG welding current [A] 15-250
MIG welding current [A] 50-250
Welding current at 60% duty cycle [A] 250 (MMA/TIG/MIG)
Welding current at 100% duty cycle [A] 193 (MMA/TIG/MIG)
3. OPERATION
3.1 GENERAL NOTES
• The device must be applied according to its purpose, with observance of OHS regulations and
restrictions resulting from data included in the rating plate (IP level, operation cycle, supply voltage,
etc.).
• The machine must not be opened as it will cause warranty loss and, in addition, exploding, unshielded
elements can cause serious injuries.
• The producer does not bear any responsibility for technical changes in the device or material losses
caused by the introduction of the said changes.
• In case of incorrect device operation, contact the service centre.
• Louvers must not be shielded – the welder must be positioned at 30 cm distance from objects
surrounding it.
• The welder must not be kept under your arm or near to your body.
• The machine must not be installed in rooms with aggressive environments, high dustiness and near
devices with high electromagnetic eld emission.
3.2 DEVICE STORAGE
• The machine must be protected against water and moisture.
• The welder must not be positioned on heated surfaces.
• The device must be stored in a dry and clean room.
3.3 CONNECTING THE DEVICE
3.3.1 Connecting the power
• Connection of the device must be performed by a qualied person. In addition, a person with required
qualications should check if the earthing or electrical installation with protection system is in line with
the safety regulations and if they operate correctly.
• The device must be placed near the work station.
• Connection of excessively long conduits to the machine must be avoided.
• One-phase welders should be connected to the socket tted with an earthing prong.
• Welders powered from a 3-Phase network are delivered without a plug, the plug must be obtained
independently and installation should be assigned to a qualied person.
PLEASE NOTE! THE DEVICE MAY ONLY BE USED UPON CONNECTION TO AN
INSTALLMENT WITH A PROPERLY FUNCTIONING FUSE!
4. OPERATION
S-MIGMA 250.IGBT WELDING MACHINE
Machine description:
Rear view:
Inside view:
1
2
3
4
5
6
7
8
9
11
13
12
10
Front view:
14
15 16
17
18
20
19
21
1. Nozzle
2. Collet
3. MIG welding torch
1
2
3
MIG torch:
EN
Bekijk gratis de handleiding van Stamos S-MIGMA 250.IGBT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Stamos |
| Model | S-MIGMA 250.IGBT |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8734 MB |
