Stairville All FX Bar handleiding
Handleiding
Je bekijkt pagina 7 van 32
CAUTION!
Risk of injury from laser!
This device contains a class 2M laser, classied according to EN 60825-1:2014+A11:2021. The accessible laser radiation is in a
wavelength range of 400 nm to 700 nm, the output is 1 mW or less. If the beam cross-section is bundled by optical collecting
instruments, looking into the laser beam can cause injuries to the eyes and aect the person’s vision temporarily. As the operator,
observe the applicable legal duties regarding safe operation before putting the device into service. Install the laser system in such
a way that persons are not at risk while it is in operation. Do not look into the laser beam for any longer period of time. Do not use
optical collecting instruments (such as magnifying glasses or lenses) to look into the laser beam, and ensure that laser beams are
not directed to areas where optical collecting instruments are used. Have all work and repairs on class 2M lasers performed by
trained experts. Never open a class 2M laser and do not make any technical changes. If you are unsure how to handle the laser
safely, include a laser protection representative in your planning.
CAUTION!
Risk of injury due to stray laser radiation!
Additional components inadequately secured to the device as well as reective objects and surfaces at the operating location can
cause stray laser radiation, which can cause injuries. Make sure that additional components are always secured adequately. Make
sure there are no reective objects or surfaces in the range of the laser beams.
NOTICE!
Risk of re due to covered vents and neighbouring heat sources!
If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can
overheat and burst into ames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other
heat sources. Never operate the device in the immediate vicinity of naked ames.
NOTICE!
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the
ambient conditions specied in the “Technical specications” chapter of this user manual. Avoid operating it in environments
with direct sunlight, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature uctuations. If
temperature uctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the
device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in oper‐
ation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by
qualied specialists at regular intervals to prevent damage due to overheating and other malfunctions.
NOTICE!
Damage to the device due to high voltages!
The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess
voltages can also cause a risk of injury and res. Make sure that the voltage specication on the device matches the local power
grid before plugging in the device. Only operate the device from professionally installed mains sockets that are protected by a
residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or it
the device will not be used for a longer period.
NOTICE!
Risk of re by exceeding the maximum current
The device can supply power to other devices of identical design and connected in series. If too many devices are connected, the
power consumption can exceed the maximum permitted power consumption, which can cause the device to overheat and burst
into ames. Only connect devices of identical design to the device. When deciding how many devices you can connect in series,
make sure that the maximum permitted power consumption as stated on the device is not exceeded. Also refer to the specica‐
tions in the technical specications for the device. Only use power cords with a cable cross-section designed for the required
current intensity when connecting the devices in series.
NOTICE!
Risk of re due to installation of a wrong fuse!
Using fuses of a dierent type than compatible with the device may cause a re and seriously damage the device. Only use fuses
of the same type. Observe the labelling on the device casing and the information in the "Technical data” chapter.
NOTICE!
Risk of re due to incorrect polarity!
Incorrectly inserted batteries may cause res and destroy the device and the batteries. Observe the markings on the batteries and
on the device. Ensure that proper polarity is observed when inserting batteries.
NOTICE!
Possible damage due to leaking batteries!
Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for
an extended period of time.
Safety instructions
All FX Bar
7
LED Eect
Bekijk gratis de handleiding van Stairville All FX Bar, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Stairville |
| Model | All FX Bar |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2667 MB |
