Stadler Form Erik handleiding
Handleiding
Je bekijkt pagina 10 van 100
2. If you would like to use the aroma diffuser function and the fireplace
effect, lift off the top part (2) and fill the water tray (3) to the maximum
mark with clean, cold tap water. Then put the top part (2) back on the
bottom part (3). Important: Transport Erik very carefully and keep him
upright when filled with water. The water could splash out of the inte-
rior tank and into the electronics. No water is required for the heating
function.
3. Switch on the appliance by pressing the On/Off button (8) on the appl-
liance or the remote control. When you put the device into operation, the
aroma diffuser function and the fireplace effect (colour Amber Light™)
are switched on by default. The heating function is deactivated. The
LEDs above the control buttons light up white.
4. The remote control (6) operates via infrared – for this purpose, point the
remote control at the infrared receiver on the front of the unit. The bat-
tery compartment (7) is located on the bottom of the remote control (6)
and is equipped with a child safety lock. To open it, push the small slider
inwards and pull out the battery compartment (Type CR2032 battery).
5. By pressing the button for controlling the fireplace effect (9) several
times, you can change / deactivate the colour of the LED lighting (Amber
Light™ – red – blue – green – light off – light and aroma diffuser off).
If the fireplace effect and the aroma diffuser are switched off, the LED
above the button (9) no longer lights up. To reactivate the lighting and
the fireplace effect, press the button (9) again.
6. You can also use Erik to fragrance the room. We ask that you be sparing
when dealing with fragrances as too much can lead to malfunctions and
damage to the unit. To use fragrances, remove the top part (2) and add
2–3 drops of your favourite liquid fragrance directly into the water. It is
not necessary to mix them as the ultrasonic membrane (15) does this
for you. If the fragrance is not intensely enough, you can increase the
number of drops.
7. The appliance switches off automatically when water needs to be re-
filled. Remove the top part (2) and fill the water up to the maximum
mark. Place the top part (2) back on the bottom part (3) and press the
button for controlling the fireplace effect (9). The appliance will resume
operation after a few seconds. Note: If the heating function is activated,
only the fireplace effect switches off and the fan heater continues to
run.
8. To control the heating function, press the button for selection of heat
output level (10). You can choose between three different modes:
LOW = 800 W (press once
HIGH = 1’500 W (press twice)
OFF = Heating function deactivated (press three times)
To reactivate the heating function, press the button for selection of heat
output level (10) again. If the heating function is active, the LEDs above
the control buttons light up red. “LOW” is activated by default.
9. The target temperature can be set using the button for the thermostat
(11). You can choose between four different modes: 18 °C (press once)
/ 20 °C (press twice) / 22 °C (press three times) or continuous opera-
tion “CO” (press four times). “CO” (continuous operation) is activated
by default.
Info: The appliance switches off the heating element when the target
temperature is reached. The fan remains switched on for 30 seconds at
Bekijk gratis de handleiding van Stadler Form Erik, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Stadler Form |
| Model | Erik |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9084 MB |