Scheppach VC20 handleiding
Handleiding
Je bekijkt pagina 20 van 204
www.scheppach.com
20
|
GB
Installing the suction hose (Fig. 8, 9)
Connect the suction hose (13) to the corresponding
port, depending on the desired use, on the wet and dry
vacuum cleaner.
Vacuuming:
Connect the suction hose (13) to the suction hose port
(8). To do so, slide the end of the suction hose (13) into
the suction hose port (8). Make sure the plug-in tting on
the end of the suction hose (13) latches into the recess
on the suction hose connection (8). In the end position,
turn the suction hose (13) in a clockwise direction.
Blowing:
Connect the suction hose (13) to the blowing function
connection port (11). Make sure the plug-in tting on
the end of the suction hose (13) latches into the recess
on the connection with blast function (11). In the end
position, turn the suction hose (13) in a clockwise di-
rection.
Mount the plastic extension tubes (18), suction
hose (13) and nozzles (16+17) (Fig. 10)
Connect the plastic extension tubes (18) together. Con-
nect the assembled plastic extension tubes with the
bent end of the suction hose (13). Fit the oor nozzle
(16) or joint nozzle (17) to the other end of the assem-
bled plastic extension tubes.
8. Operation
Warning! Switch the device o if liquid or foam
emerges with the exhaust air during wet vacuuming.
Switching on/o (Fig. 1)
Press the on/o switch (9):
• Switch setting 0: O
• Switch setting I: On
Dry vacuuming
Use the paper lter bag (15) and the textile lter (19) for
dry vacuuming.
Wet vacuuming
Use the foam lter (14) for wet vacuuming. Ensure that
the foam lter (14) is correctly tted.
If the stainless steel container (7) is full, the safety oat
valve (12) closes the suction port and suction operation
is interrupted.
6. Technical data
Mains voltage 220-240 V~ 50/60 Hz
Power 1300 W
Water tank capacity 20 l
Suction performance 20 kPA
Protection category IPX4
Protection class II
7. Assembly
m Attention!
Always make sure the product is fully assembled
before commissioning!
Installation of the castors (Fig. 4)
1. Press the four castors (5) into the holes in the
wheel mounting base.
Installing the machine head (2) (Fig. 5)
1. Place the machine head (2) on the stainless steel
container (7). Secure the machine head (2) with
the locking hooks (4). When installing the machine
head (2), ensure that the locking hooks (4) latch
into place correctly.
Installing the foam lter (14) (Fig. 6)
Never use the device without lter! Always ensure
that the lters are correctly tted.
Installing the foam lter (14): For wet vacuuming, slide
the foam lter (14) provided over the lter basket with
safety oat valve (12).
Installing the textile lter (19) (Fig. 6a)
Never use the device without lter! Always ensure
that the lters are correctly tted.
For dry vacuuming, slide the textile lter (19) provided
over the lter basket with safety oat valve (12).
Installing the paper lter bag (15) (g. 7)
It is recommended to use an additional paper lter bag
(15) when vacuuming ne, dry dirt. Slide the paper lter
bag (15) over the suction opening in the stainless steel
container (7). The paper lter bag (15) is only suitable
for dry vacuuming. The paper lter bag (15) makes it
easier to dispose of the dust collected.
Bekijk gratis de handleiding van Scheppach VC20, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | VC20 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 26479 MB |
