Scheppach PX-UG-2000R handleiding
Handleiding
Je bekijkt pagina 18 van 28
w ww.practixx.com
18
|
GB
10. Maintenance
General maintenance tasks
• We recommend that you clean the product directly
after every use.
• Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product.
11. Repair & ordering spare parts
After repairs or maintenance, make sure that all safe-
ty-related parts are installed and are in perfect con-
dition. All parts which may cause injury must be kept
where they are inaccessible to children or others.
Attention: According to the German Product Liability
Act, no liability is accepted for damage caused by im-
proper repairs or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialist. The same applies to
accessory parts.
11.1 Ordering spare parts
Please provide the following information when order-
ing spare parts:
• Article number of the product
Service information
With this product, it is necessary to note that the follow-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consuma-
bles.
Wearing parts*: Adjustable support arm
* may not be included in the scope of delivery!
Spare parts / accessories
Adjustable support arm - Article no.: 4907101005
Spare parts and accessories can be obtained from our
Service Centre. To do this, scan the QR code on the
front page.
12. Storage and transport
Attention!
Do not transport whilst the electric power tool is run-
ning.
8.7 Fastening your tabletop machine (Fig. 9)
Dierent tabletop machines can be fastened to your
tool stand (1) by adjusting the support arms (17) to the
spacing of the mounting holes on your machine.
1. Place your tabletop machine (e.g. cross-cut mitre
saw) on the support arms (17).
2. Fasten the tabletop machine with 4 at head screws
(G), 4 washers (H), 4 spring washers (I) and 4 hex-
agonal nuts (J) on each of the support arms (16).
3. Tighten the screws after assembly.
4. Fasten the support arms (17) with the mounted
tabletop machine to the tool stand (1) as described
in point 8.6.
8.8 Using the workpiece support (5) as a work-
piece stop (Fig. 10)
The workpiece supports (5) have integrated workpiece
stops (4), on both sides, which can be used to saw mul-
tiple pieces of wood to the same length.
1. Loosen the star-grip screw (6) on the required side
of the tool stand (1) and adjust the height of the
workpiece support (5) so that the workpiece stop
(4) is at the same height as the workpiece support
on the saw.
2. Loosen the grip screws (16) to slide the workpiece
support (5) horizontally.
3. Set the required distance between the saw blade
and the workpiece stop (4).
4. Fix your setting by retightening the handle and star
grip screws (6+16).
8.9 Using the material support (10) (Fig. 10)
1. The tool stand (1) has a fold-out material support
(10). Fold the material support (10) down to use it.
9. Cleaning
Attention!
Before any cleaning or maintenance work, the electric
power tool tted must be switched o and the mains
plug pulled out! Danger of injury!
• Keep the tool stand as free of dust and dirt as pos-
sible. Rub the tool stand clean with a clean cloth or
blow it o with compressed air at low pressure.
• We recommend that you clean the tool stand directly
after each use.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the tool stand.
Bekijk gratis de handleiding van Scheppach PX-UG-2000R, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | PX-UG-2000R |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3420 MB |
