Scheppach MS173-51E handleiding
Handleiding
Je bekijkt pagina 40 van 144
www.scheppach.com
40
|
GB
• Ret the transmission housing and the blade using
the screws.
Maintaining and adjusting the cables
Oil the cables at regular intervals and check that they
move easily.
Air lter maintenance (Fig. 20)
Fouled air lters diminish the engine output due to re-
duced air supply to the carburettor. Regular inspection
is therefore essential.
The air lter should be checked every 25 operating
hours and cleaned as required. The air lter must be
checked more often in case of very dusty air.
Unclip the air lter cover and remove the sponge lter
element. Replace the air lter to avoid objects falling
into the air intake (g. 20).
Attention: Never clean the air lter with petrol or com-
bustible solvents. Clean the air lter with compressed
air or simply by knocking out any soiling.
Spark plug maintenance (Fig. 21)
Check the spark plug for dirt for the rst time after 10
operating hours and clean it with a copper wire brush
if necessary. Then service the spark plug every 50 op-
erating hours
.
Remove the spark plug connector with a twist.
Remove the spark plug (10) with a spark plug wrench.
Use a feeler gauge to set the gap to 0.75 mm( 0.030”).
Replace the spark plug (10) and take care not to tighten
it too rmly.
Engine brake lever (g. 1)
The motor is equipped with a mechanical brake (3) that
must be checked regularly. When the brake lever is
released, the blade must come to a standstill within 7
seconds; if this is not the case, the appliance must not
be used. Contact an authorised specialist dealer.
Ensure that the device is in perfect condition for the
entire duration of its service life. Improper maintenance
may lead to life-threatening injuries.
Repairs
After repairs or maintenance, make sure that all safe-
ty-related parts are installed and are in perfect con-
dition. All parts which may cause injury must be kept
where they are inaccessible to children or others.
Attention: According to the German Product Liability
Act, no liability is accepted for damage caused by im-
proper repairs or by not using original spare parts.
Never attempt to bend a bent blade back to straight
again. Never mow the lawn with a bent or heavily worn
blade as this will cause vibrations and can lead to fur-
ther damage to the mower.
m Attention! There is a risk of injury if you work with
a damaged blade.
Resharpening the blade
The blades can be resharpened with a metal le. In
order to avoid an imbalance, sharpening should only be
performed by an authorised specialist workshop.
Oil level check
m Attention! Never operate the engine without oil or
with too little oil. This can cause serious damage to the
engine. Only use SAE30 engine oil.
Check the oil level (Fig. 18):
• Position the lawnmower on a straight, level surface.
• Remove the oil dipstick (12) by turning it to the left,
then wipe o the oil dipstick. Insert the dipstick back
in the lling nozzle as far as the stop, but do not
screw it back in.
• Pull out the dipstick and read the oil level horizontally.
The oil level must be positioned between the max and
min of the oil dipstick (12).
Oil change (Fig. 23)
• The engine oil change should be completed annual-
ly before the start of the season while the engine is
at operating temperature and shut o.
• Only use motor oil (SAE 30).
• Empty the fuel tank (with a petrol extraction pump)
• Place a at oil collecting tray in front of the mower
(min. volume 1 litre).
• Unscrew the oil dipstick and tilt the mower until all
the oil has drained into the collection tray.
• Then ll in fresh engine oil up to the upper mark of the
oil dipstick (approx. 0.4 l), do not overll the device.
• Attention! To check the oil level, do not screw in the
oil dipstick, but only insert it up to the thread.
Dispose of the used oil in accordance with applicable
regulations.
Cleaning the belts (Fig. 17, 19)
• Remove the blade and the transmission housing by
undoing the screws.
• Clean the elements of the transmission and the V-belt
once or twice a year with a brush or compressed air.
Bekijk gratis de handleiding van Scheppach MS173-51E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | MS173-51E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 22629 MB |
