Scheppach MS150-42E handleiding
Handleiding
Je bekijkt pagina 41 van 68
www.scheppach.com
GB
|
41
m Attention!
Always shut the engine down and remove the spark
plug connector before carrying out any cleaning work.
Wheel axles and wheel hubs
• These should be lightly greased once a season.
Blade
For safety reasons you should only ever have your blade
sharpened, balanced and mounted by an authorized
service workshop. For optimum results it is recommend-
ed that the blade should be inspected once a year.
Only ever use original spare parts when having the
blade replaced. Wear gloves when replacing the blade
in order to prevent injury.
Never have any other blade tted.
• Empty the fuel tank before removing the blade
• To replace the blade, undo the screw.
• Reinstall as illustrated in Fig. 17. Tighten the screw
properly. Tightening torque 45 Nm. When replacing
the blade, the blade screw should also be replaced.
Damaged blades
Should the blade, in spite of all precautions, come into
contact with an obstruction, shut down the engine im-
mediately and pull the spark plug boot. Tip the lawn
mower onto its side and check the blade for damage.
Damaged or bent blades must be replaced. Never at-
tempt to bend a bent blade back to straight again. Nev-
er mow the lawn with a bent or heavily worn blade as
this will cause vibrations and can lead to further dam-
age to the lawn mower.
m CAUTION! There is a risk of injury if you work with
a damaged blade.
Resharpening the blade
The blades can be resharpened with a metal le. In
order to avoid imbalance, the blade should be resharp-
ened by an authorized service workshop
Checking the oil level
m CAUTION! Never run the engine with no or too little
oil. This could cause severe damage to the engine. Use
only SAE30 engine oil.
Checking the oil level (Fig. 18):
• Stand the lawn mower on a at level surface.
• Unscrew the oil dip stick (12) by turning anticlockwise,
pull out and wipe. Insert the dip stick back in the lling
mount as far as the stop, but do not screw back in.
• Empty the petrol tank with a petrol suction pump.
• Start the engine and let it run until any remaining
petrol has been used up.
• Change the oil at the end of every season. To do so,
remove the used engine oil from a warm engine and
rell with fresh oil.
• Remove the spark plug from the cylinder head.
• Fill the cylinder with approx. 20ml of oil from an oil can.
• Slowly pull back the starter handle, which will bathe
in the cylinder wall with oil.
• Screw the spark plug back in.
• Clean the cooling ns of the cylinder and the housing.
• Be sure to clean the entire machine to protect the paint.
• Store the machine in a well-ventilated place.
Battery Pack and Charger
• When not in use, disconnect charger and store in a cool,
dry area. Wet, damp areas can cause corrosion of termi-
nals and electrical contacts. If stored for long periods in
high temperatures (120° F / 49° C), permanent damage
to the battery pack can result. Check electrical terminals
and contacts on battery packs and charger. Wipe with
clean cloth or blow clean with compressed air.
• After storage, a normal charge may be required.
To check available charge, press the Battery Fuel
Gauge button (E, Figure 24) and charge if required.
See the Battery Fuel Gauge section.
13. Maintenance
• Regular, careful maintenance is required to guaran-
tee the safety level and performance of the machine.
• Make sure that all nuts, bolts and screws are tightened se-
curely and that the machine is in safe working condition.
• Routinely check the grass basket for signs of wear
and impaired functionality.
Regularly clean the grass box with water and let it
dry thoroughly.
• For your own safety, replace worn or damaged parts
without delay.
• If the fuel tank should require emptying this should
only be done in the open air using a petrol suction
pump (available from DIY shops).
m WARNING
Never work on or touch conducting parts on the ignition
unit with the engine running. Always pull the spark plug
boot from the spark plug before starting any work of
care or maintenance. Never perform any work on the
machine while it is running. Any work not described in
these Operating Instructions must be performed by an
authorized service workshop only.
Bekijk gratis de handleiding van Scheppach MS150-42E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | MS150-42E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10920 MB |
