Scheppach HMP161-56B handleiding
Handleiding
Je bekijkt pagina 33 van 60
www.scheppach.com
GB
|
33
10.1 Filling up with engine oil (Fig. 14)
ATTENTION
The product is delivered without engine oil. There-
fore, ensure that you add oil before starting it up.
Use multigrade oil (SAE 30, 10W-30 or 10W-40).
Check the oil level regularly before commissioning.
An oil level that is too low can damage the motor.
1. Unscrew the oil dipstick (17).
2. Fill the tank with engine oil using a funnel. Note
the max. lling capacity of 0.4 l. Fill the oil up to
the lower edge of the lling nozzle carefully.
3. Wipe the oil dipstick (17) with a clean, lint-free cloth.
4. Re-insert the oil dipstick (17) and pull it out again.
Check the oil level without screwing the oil dip-
stick (17) back in.
5. The oil level must be within the middle mark on
the oil dipstick (17).
6. If the oil level is too low, add the recommended
amount of oil (max. 0.4 l).
7. Then screw the oil dipstick (17) back in.
10.2 Filling up with fuel (Fig. 1)
m DANGER
Risk of re and explosion!
When lling, fuel may ignite and even explode.
This can lead to severe burns or death.
• Switch o the motor and allow it to cool down
• Keep heat, ames and sparks away.
• Only ll up with fuel outdoors.
• Wear protective gloves.
• Avoid contact with skin and eyes.
• Start the product at a distance of at least 3 m from
the fuel lling point.
• Watch out for leaks. If fuel is leaking, do not start
the engine.
ATTENTION
The product is delivered without fuel. It is therefore
essential to ll with fuel before commissioning. Use
Super E10 petrol for this.
1. Clean the area surrounding the lling area. Impu-
rities in the fuel tank (18) lead to operational faults.
2. Carefully open the tank cover (19) so that any pos-
sible overpressure can be relieved.
3. Fill the fuel tank (18) with petrol using a funnel.
Note the max. lling capacity of 1.2 l. Fill the petrol
up to the lower edge of the lling nozzle carefully.
4. Close the tank cover (19) again. Ensure that the
fuel cap is tightly sealed.
5. Clean the tank cover (19) and the surroundings.
6. Turn the trim plate (15) outwards into position (Fig. 5)
7. Fasten the trim plate (15) with two pan-head
screws (13) (Fig. 6).
10. Before commissioning
ATTENTION
Always assemble the product completely be-
fore commissioning!
m WARNING
Health hazard!
Inhalation of fuel / lubricating oil vapours and ex-
haust gases can cause serious damage to health,
unconsciousness and in extreme cases death.
- Do not inhale fuel/lubricating oil vapours and
exhaust fumes.
- Operate the product outdoors only.
ATTENTION
Product damage!
Using the product without or with too little engine
and gear oil can result in engine damage.
- Fill with fuel and oil before commissioning. The
product is supplied without engine and gear-
box oil.
ATTENTION
Environmental damage!
Spilled oil can pollute the environment permanent-
ly. The liquid is highly toxic and can quickly lead to
water pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a lling nozzle or funnel.
- Collect drained oil in a suitable container.
- Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
- Dispose of oil as per local regulations.
ATTENTION
Risk of damage!
If incorrectly stored or undrained fuel is used, the
carburettor may become clogged or engine opera-
tion may be aected.
- Put unused fuel in an airtight vessel and store
it in a dark, cool room.
Place the product on a level, even surface.
Tool required: (not necessarily included in the scope
of delivery!)
- Measuring cup 1 litre (oil/fuel resistant)
- Funnel
- Lappen
Bekijk gratis de handleiding van Scheppach HMP161-56B, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HMP161-56B |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9694 MB |
