Scheppach HBS25 SE handleiding
Handleiding
Je bekijkt pagina 28 van 56
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
8 Assembly
ATTENTION
Always make sure the product is fully assembled
before commissioning!
WARNING
Pull out the mains plug before carrying out
any setting, servicing or repair work!
Tool required:
• Slotted screwdriver* (A)
• 1x open-ended spanner, AF 10/13 mm* (B)
• 1x Allen key 3 mm* (C)
• 1x Allen key 4 mm* (D)
• 1x Allen key 5 mm* (E)
* = may not be included in the scope of delivery!
8.1 Assembling the saw table (7) (Fig.
4-6)
1. Remove the wing nut (22), the locking handle (23), the
two washers and the clamping plate (24).
2. Then remove the two knurled nuts (7b), the U-rein-
forcement (7a) and the two countersunk screws
M6x18 from the saw table (7). Use the 4 mm Allen key
(D).
3. Guide the saw table (7) over the band saw blade (17).
Fasten it to the two screws on the frame (14) with the
clamping plate (24), the two washers, the locking han-
dle (23) and the wing nut (22).
4. Mount the U-reinforcement (7a) to the bottom of the
saw table (7) with two countersunk screws M6x18 and
two knurled nuts (7b). Use the 4 mm Allen key (D).
8.2 Which band saw blade to use
Check that the tool attachment is fitted securely.
Tool attachments that are not fitted correctly or securely
may come loose during operation and injure you.
The band saw blade included in the scope of delivery is
intended for universal use. The following criteria should
be considered when selecting the band saw blade:
• It is possible to cut tighter radii with a narrow band
saw blade than with a wide band saw blade.
• Use wide band saw blades to perform straight cuts.
This is important in particular when cutting wood. The
band saw blade has a tendency to follow the wood
grain and therefore deviates easily from the desired
position.
• Fine-toothed band saw blades cut more smoothly, but
also more slowly than coarse band saw blades.
• Only use undamaged band saw blades that are in per-
fect condition. Band saw blades that are bent, blunt or
damaged in any other way can break.
8.3 Tensioning the band saw blade
(17) (Fig. 1)
ATTENTION
If the band saw is at a standstill for an extended period,
the band saw blade tension must be relieved, i.e. before
switching the band saw on it is necessary to check the
band saw blade tension.
1. To tension the band saw blade (17), turn the clamping
screw (1) clockwise.
Notes:
• The correct tension of the band saw blade can be de-
termined by pressing the finger laterally against the
band saw blade, roughly centrally between the two
band wheels (2+8). The band saw blade should only
depress slightly (approx. 1-2 mm) here.
• The sufficiently tensioned band saw blade makes a
metallic sound when tapped.
• Relieve the band saw blade tension if it is not in use
for an extended time, so that it does not become over-
stretched.
ATTENTION
With high tension, the band saw blade may break.
ATTENTION
Danger of injury!
If the tension is too low, the driven band wheel may
spin, resulting in the band saw blade coming to a stand-
still.
1. To relieve the band saw blade (17), turn the clamping
screw (1) anti-clockwise.
8.4 Adjust the band saw blade (17)
(Fig. 1, 2)
ATTENTION
Before it is possible to implement the band saw blade
setting, the band saw blade must be tensioned correct-
ly.
1. Open the housing doors (11) by loosening the door
lock (10). Use the slotted screwdriver (A).
2. Turn the top band wheel (2) clockwise slowly. The
band saw blade (17) must run in the centre on the
running surfaces (3) of the top band wheel (2).
If this is not the case, correct the angle of the top band
wheel (2).
3. To do this, open the wing nuts (13a).
– If the band saw blade (17) runs more towards the
rear edge of the band wheel (2), then the adjust-
ment handle (13) must be rotated anti-clockwise.
28 | GB www.scheppach.com
Bekijk gratis de handleiding van Scheppach HBS25 SE, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HBS25 SE |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8367 MB |
