Scheppach GP1400JET handleiding
Handleiding
Je bekijkt pagina 22 van 80
www.scheppach.com
22
|
GB
3. Attach the suction and pressure lines so that
they do not exert any mechanical pressure on the
pump.
4. The suction line should be located deep enough in
the water to prevent the pump from running dry if
the water level drops.
5. A leaking suction line will prevent the water from
being sucked in due to air ingress.
6. Avoid sucking in foreign bodies (sand etc.).
Filling the pump with water (Fig. 3)
m NOTE!
To reduce the start-up time of the pump and to prevent
air from being sucked in, the pump must be lled with
water beforehand!
1. The suction line should already be tted for this
purpose to prevent water from owing out of the
suction connection (6).
2. Use the opening of the pressure connection (1) to
ll the pump with water. Alternatively, water can
be poured in through the opening of the pre-lter
plug (7).
3. Slightly tilt the pump now and then, to avoid air
being trapped.
4. Now, attach the pressure line as described in the
next point.
Fitting of a pressure line (Fig. 1)
1. Connect the pressure line (at least 19 mm (3/4”))
directly or via a threaded nipple to the pressure
connection (1) approx. 30.75 mm (T1”) of the
pump.
2. During the suction process, open the shut-off de-
vices (spray nozzles, valves, etc.) in the pressure
line completely so that the air present in the suc-
tion line can escape freely.
10. Start up
m Attention!
Always make sure the product is fully assembled
before commissioning!
1. Place the product on a rm, level and horizontal
location.
2. Open the pressure line.
3. Connect the mains lead.
4. Switch the product on using the on/off switch (3).
Suction can take up to 5 minutes at max. suction
head.
Information about noise level measured in accord-
ance with EN ISO 3744:2010
Noise data
Sound power level L
WA
85 dB
Sound pressure level L
pA
70.34 dB
Uncertainty K
wa/pA
1.64 dB
8. Unpacking
• Open the packaging and carefully remove the prod-
uct.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the rst time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
m WARNING!
The product and the packaging material are not
children‘s toys! Do not let children play with plas-
tic bags, lms or small parts! There is a danger of
choking or suffocating!
9. Layout
Warning!
Always remove the mains plug before carrying out ad-
justments on the product.
Fitting of a suction line (Fig. 1)
1. Screw a suction hose (plastic hose at least 19 mm
(3/4”) directly or with a threaded nipple to the suction
connection (6) approx. 30.75 mm (T1”) of the pump.
2. Lay the suction line from the water pick-up point to
the pump in a continuously rising slope. Please do
not lay the suction line above the pump height. Air
bubbles in the suction line will delay and prevent
the suction process.
Bekijk gratis de handleiding van Scheppach GP1400JET, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | GP1400JET |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10412 MB |
