Scheppach AWH-500BL handleiding
Handleiding
Je bekijkt pagina 25 van 212
www.scheppach.com
GB
|
25
8. Cleaning and maintenance
8.1 Cleaning
• Keep the automatic welding mask as free of dust and
dirt as possible. Wipe the appliance with a clean cloth
or use a slightly damp cloth and a little soft soap.
Do not use any cleaning products or solvents; they
could attack the plastic parts of the device.
• Make sure that no water or moisture gets into the
device.
• We recommend that you clean the device directly
after every use.
8.2 Changing the battery (Fig. 3)
You can replace batteries with a low charge via the
battery compartment. A low battery charge is indicat-
ed by the battery indicator 16 with a red warning light.
• Open battery compartment 15 by turning the cover
of battery compartment 15 anti-clockwise (Fig. 3).
• Once you have removed the cover of battery com-
partment 15, you can remove the battery.
• When inserting a new battery (CR2032), you must
observe the correct polarity. The positive pole mark-
ing “+” must point upwards.
8.3 Replacing the front panel (6) / rear panel (9)
8.3.1 Replacing the front panel (6) (Fig. 4)
Remove the front panel (6) from the helmet without
tools and replace it with a new one.
8.3.2 Replacing the rear panel (9) (Fig. 5)
Remove the rear panel (9) from the helmet without
tools and replace it with a new one.
8.4 Ordering spare parts
Only use original accessory parts:
Frequently ordered accessories: Article number:
Front panel 7906610701
Rear panel 7906610702
8.5 Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are
required as consumables.
Wearing parts*: Front panel, rear panel, battery
* may not be included in the scope of delivery!
6.6.3 Setting the sensitivity
With the sensitivity setting (12) it is possible to control
the light sensitivity of the sensor. Switching the lter
to darkening can be continuously adjusted between HI
(high = high sensitivity) and LO (low = low sensitivity)
using the “SENSITIVITY” control on the inside of the
helmet.
In the event of low light incidence, it is possible to set
the controller to the highest level so that automatic
darkening occurs even with a weak light source. Set
the sensitivity to the highest level before welding and
adjust accordingly during welding if necessary.
7. Technical data
Field of vision 92 x 42 mm
UV/IR lter size 110 x 90 x 9 mm
Light level (grind) DIN 4
Dark level DIN 9 - DIN 13
Switching time (light to
dark)
<0.5 ms
Delay time 0.1 - 1 s
UV / IR protection class DIN 16
Switching on/o Automatic
Power supply
Solar cell + 1x CR2032
lithium button cell
(battery replacement
required)
Grinding function Yes
Working temperature -5°C - +55°C
Storage temperature -20°C - +70°C
Weight approx. 0.46 kg
Welding processes
SMAW, MAG, TIG/
GTAW, MIG (heavy),
MIG (light), PAC, PAW
max. service life 2000 hours
Subject to technical changes!
Bekijk gratis de handleiding van Scheppach AWH-500BL, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | AWH-500BL |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 28998 MB |
