Ryobi One+ RPP182020C handleiding
Handleiding
Je bekijkt pagina 5 van 24
5
Original Instructions
kickback forces. Kickback forces can be controlled
by the operator if proper precautions are taken. Do
not let go of the product.
● Do not overreach. This helps prevent unintended tip
contact and enables better control of the product in
unexpected situations.
● Use only replacement bars and chains specified by
the manufacturer. Incorrect replacement bars and
chains may cause chain breakage or kickback.
● Sharpening the chain safely is a skilled task. The
manufacturer strongly recommends that a worn
or dull chain is replaced with a new one. The part
number is available in the product specifications
table in this manual.
ADDITIONAL BATTERY SAFETY WARNINGS
■ To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the
product, battery pack, or charger in fluid or allow fluid
to flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■ Charge the battery pack in a location where the ambient
temperature is between 10 °C and 38 °C.
■ Store the battery pack in a location where the ambient
temperature is between 0 °C and 20 °C.
■ Use the battery pack in a location where the ambient
temperature is between 0 °C and 40 °C.
TRANSPORTATION AND STORAGE
■ Power off the product, and remove the battery pack.
Make sure that all moving parts have come to a
complete stop. Allow the product and the battery pack to
cool down before storing or transporting.
■ Remove all foreign materials from the product.
■ Do not store or transport the product with the battery
pack fitted. Remove the battery pack, and secure it
separately. Store the product in a cool, dry, and well-
ventilated place that is inaccessible to children. Keep
the product away from corrosive agents, such as garden
chemicals and de-icing salts. Do not store the product
outdoors.
■ Fit the blade cover before storing the product or during
transportation.
■ When storing the product for a long period of time (one
month or longer), make sure that the chain is lightly
lubricated to prevent rust.
■ Store the product in a location where the ambient
temperature is between 0 °C and 40 °C.
■ When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
or damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery pack in accordance with local and
national provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
■ Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■ Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■ You may make adjustments and repairs that are
described in this manual. For other repairs, have the
product serviced by an authorised service centre only.
■ Power off the product, and remove the battery pack.
Allow both to cool down. Make sure that all moving parts
have come to a complete stop before any cleaning or
maintenance task.
■ The saw chain is very sharp. To prevent personal
injury, exercise extreme caution when cleaning, fitting,
or removing the blade cover. Always wear protective
gloves when performing maintenance on the chain.
■ Improper chain maintenance increases the potential of
kickback. Failure to replace or repair a damaged chain
can cause serious injury.
■ Follow instructions for lubricating the product and for
checking and adjusting the chain tension.
■ After each use, clean the body and handles of the
product with a soft, dry cloth. Any part that is damaged
should be properly repaired or replaced by an authorised
service centre.
■ Check all nuts, bolts, and screws before each use and
at frequent intervals for proper tightness to ensure that
the product is in safe working condition. Any part that is
damaged should be properly repaired or replaced by an
authorised service centre.
MAINTENANCE SCHEDULE
The bar may be reversed to distribute wear for maximum life.
The bar should be cleaned every day of use and checked for
wear and damage.
Daily check
Bar lubrication Before each use
Chain tension Before each use and frequently
Chain sharpness Before each use (visual check)
For damaged parts Before each use
For loose fasteners Before each use
KNOW YOUR PRODUCT
See page 7.
1. Chain lubricant cap
2. Saw chain
3. Bar nut
4. Guide bar
5. Ribbed bumper
6. Sprocket cover
7. Chain tensioning screw
8. Extension pole
Bekijk gratis de handleiding van Ryobi One+ RPP182020C, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ryobi |
| Model | One+ RPP182020C |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3104 MB |
