Ryobi One+ RPP182020C handleiding
Handleiding
Je bekijkt pagina 4 van 24
4
Original Instructions
● before inspecting the product after striking a foreign
object
● before performing maintenance
● whenever the product starts to vibrate abnormally
■ Do not modify the product in any way or use parts
and accessories that are not recommended by the
manufacturer. This may increase the risk of serious
injury to yourself or others.
■ Injuries may be caused, or aggravated, by prolonged use
of the product. When using the product for prolonged
periods, ensure to take regular breaks.
■ If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately power off the product
and inspect it for damage or identify the cause of the
vibration. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
PERSONAL PROTECTIVE EQUIPMENT
Good quality personal protective equipment, as used by
professionals, helps reduce the risk of injury to the operator.
The following items should be used when operating your
product:
■ Safety helmet
■ Hearing protection
■ Eye and face protection
■ Gloves
■ Footwear
OPERATION
■ Operate the product only in temperatures between 0 °C
and 40 °C.
■ Study the condition of the tree and branches before
starting work. If there are signs of damage, rot, or decay,
do not attempt to prune on your own. Damaged or rotten
branches are highly unstable. Seek the services of a
professional tree surgeon.
■ Never stand under the branch to be pruned.
■ Pruned branches do not always fall cleanly to the ground.
They are easily caught and deflected by other foliage.
Ensure that a safety zone at least twice the length of
the branch to be cut is available and maintained during
pruning. If this is not possible, seek the services of a
professional tree surgeon.
■ Beware of falling branches or those that rebound after
hitting the ground.
■ Ensure that the falling branch is not a danger to yourself,
bystanders, or property, including utility cables.
■ During operation, hold the product with both hands. Use
one hand to firmly grasp the front hand grip. Use the
other hand to grasp the rear handle and to operate the
trigger release and the on/off trigger.
■ Hold the product by the insulated gripping surfaces only,
because the saw chain may contact hidden wiring. Saw
chains contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the operator
an electric shock.
■ Use the harness if it is supplied with the product. The
harness assists in controlling the drop of the product
after the cut is completed. The harness also helps
support the weight of the product during use and while
moving between cutting positions. Carefully adjust the
harness to fit comfortably and help support the weight
of the product.
■ Identify the quick-release mechanism and practice using
it before you start using the product. The correct use of
the quick-release mechanism may prevent serious injury
in the case of an emergency. Never wear additional
clothing over the harness or otherwise restrict access to
the quick-release mechanism.
■ Never operate the product with the pole at an angle of
greater than 60° from the horizontal.
■ Do not try to cut the branch too close to the tree trunk.
Leave about 15 cm from the trunk to the cut.
■ Rest the saw bar on the branch to be pruned and push
the saw gently forwards so that the ribbed bumper also
contacts the branch. This aids stability and cutting and
provides cleaner cuts.
■ Small and thin branches that are not heavy can be cut
with one cut using the bottom of the saw bar.
■ Use extreme caution when cutting small-size bush and
saplings because slender material may catch the saw
chain and be whipped toward you or pull you off-balance.
■ When cutting a limb that is under tension, be alert for
springback so that you will not be struck when the
tension in wood fibres is released.
■ Branches that are larger in diameter and are heavier
may break or split during the cut, so make a first cut
from under the branch using the top of the saw bar. The
first cut should be approximately one-third of the way
through the branch.
■ Consider pruning large branches in manageable
sections rather than as a whole.
■ Never try to restart a previous cut with the chain and bar
in the earlier cut. Always start a new cut. This reduces
the risk of kickback and potential injury.
■ If the cutting performance deteriorates over time, check
if the chain teeth are sharp and clean. If necessary,
replace the original chain (and bar) as recommended by
the manufacturer.
■ If the chain and bar become pinched or trapped in
branches that are too high to reach, seek advice from
a professional tree service specialist about the safe
removal of the cutting means.
■ Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closes in and
pinches the saw chain in the cut. Tip contact in some
cases may cause a sudden reverse reaction, kicking the
guide bar up and back towards the operator. Pinching
the saw chain along the top of the guide bar may push
the guide bar rapidly back towards the operator. Either
of these reactions may cause you to lose control of the
product, resulting in serious personal injury. Do not
rely exclusively upon the safety devices built into the
product. As a product user, take several steps to keep
cutting jobs free from accident or injury. Kickback is the
result of tool misuse or incorrect operating procedures
or conditions, and can be avoided by taking the following
precautions:
● Make sure that the area in which you are cutting
is free from obstructions. Do not let the nose of
the guide bar contact a branch, limb, or any other
obstruction while operating the product.
● Maintain a firm grip with both hands on the product,
and position your body and arm to allow you to resist
Bekijk gratis de handleiding van Ryobi One+ RPP182020C, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ryobi |
| Model | One+ RPP182020C |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3104 MB |
