Ryobi One+ P2860 handleiding
Handleiding
Je bekijkt pagina 12 van 38
8 — English
FILLING THE TANK
See Figures 5 - 6.
WARNING:
Before filling the tank, always remove the battery pack
and ensure the battery cover is closed. Wipe up any spills
before inserting the battery pack. Following this rule will
reduce the risk of electric shock and corrosive liquids
entering the battery pack, which can cause battery pack
failure including short circuit resulting in smoke, fire, and/
or serious personal injury.
WARNING:
Always follow the chemical manufacturer’s instruc-
tions printed on their product labeling for use, cleaning,
and storage. Do not combine chemicals. Clean thor-
oughly after each use, following the instructions in the
Maintenance section of this manual. Chemicals should
be stored out of the reach of children. Failure to do so
may result in serious personal injury.
WARNING:
Do not allow conductive or corrosive fluids to get inside
the battery pack. If conductive or corrosive fluids are
spilled on the battery, refer to the instructions in your
battery operators manual.
When adding spray solutions, you may add water and the
desired chemical solution directly into the tank, or use a
solution that has been premixed in a separate container,
then poured into the sprayer, using a funnel if needed. For
either method, remember:
Liquids used must be as thin as water. Thicker liquids will
not spray properly.
Do not overfill the tank.
NOTE: If using a measuring container or funnel to fill the
tank, be sure to thoroughly clean and rinse these items after
use. If premixing the spraying solution, rinse the container
used for mixing.
To fill:
Remove the battery pack.
Unscrew the cap and remove it from the tank.
Fill the tank with the desired amount of liquid (up to
4gallons).
NOTE: To ensure proper operation of the sprayer, do not
fill past the max fill line.
Screw the cap back onto the sprayer, making sure it is
tightened securely.
NOTE: Wipe the outside of the tank with a dry cloth and
clean up any spills before inserting the tank.
Reinstall the battery pack.
NOTICE:
It is important to thoroughly clean the unit after each use.
Allowing liquid to remain in an idle tool for an extended
period may cause its moving pieces and connectors to
seize up.
INSTALLING/REMOVING BATTERY PACK
See Figure 7.
WARNING:
Always remove battery pack from your tool when you are
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental
starting that could cause serious personal injury.
To install:
Raise the battery cover.
Align the raised rib on the battery pack with groove in
the battery port and place the battery pack in the tool.
Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in the
tool before beginning operation.
Lower the battery cover.
To remove:
Depress the latches on both sides of the battery pack
to release the battery pack and remove it from the tool.
WARNING:
Risk of fire or explosion. Spray area must be well-
ventilated and away from sparks or flames.
TURNING THE SPRAYER ON/OFF
See Figures 8 - 9.
Turn the control knob clockwise to turn the sprayer ON
and to adjust fluid pressure.
Turn the control knob clockwise to increase the pressure
and counterclockwise to decrease the pressure.
NOTE: To apply more spray to an area, increase the pres-
sure. To apply less spray, decrease the pressure.
To start the flow of liquid at the spray wand, squeeze
the trigger.
OPERATION
Bekijk gratis de handleiding van Ryobi One+ P2860, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ryobi |
| Model | One+ P2860 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4644 MB |
