Roland S-2416 handleiding
Handleiding
Je bekijkt pagina 24 van 28

Appendix
24
Main Specications
Roland S-2416: STAGE UNIT
Number of Channels 32 in 24 out
AD Conversion
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
DA Conversion
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
Frequency Response -2 dB/+0 dB (Input Gain: +4 dBu, 10 Hz–40 kHz, Sample Rate: 96 kHz, typ.)
Total Harmonic Distortion + Noise 0.007 % (Pad: O, Input Gain: -10 dBu, 20 Hz–20 kHz, typ.)
Dynamic Range INPUT jacks (1–24): 110 dB (typ.)
Channel Separation (1 kHz)
INPUT jacks (1–24): 103 dB (Input Gain: +4 dBu, IHF-A, typ.)
OUTPUT jacks (1–16): 110 dB (typ.)
Nominal Input Level (Variable)
-65–-10 dBu (PAD: O)
-45–+10 dBu (PAD: On)
Non Clip Maximum Input Level INPUT jacks (1–24): +28 dBu (1 kHz, 10 kΩ load, typ.)
Input Impedance INPUT jacks (1–24): 7 kΩ
Nominal Output Level OUTPUT jacks (1–16): +4 dBu (Load impedance: 10 kΩ, typ.)
Maximum Output Level OUTPUT jacks (1–16): +22 dBu (Load impedance: 10 kΩ, typ.)
Output Impedance OUTPUT jacks (1–16): 600 Ω (typ.)
Recommended Load Impedance OUTPUT jacks (1–16): 10 kΩ or greater
Residual Noise Level (IHF-A, typ.) OUTPUT jacks (1–16): -84 dBu
Equivalent Input Noise Level (E.I.N.) INPUT jacks (1–24): -128 dB (Input Gain: -65 dBu, IHF-A, typ.)
Network Latency 375 µs when using REAC cable only (AD to REAC to DA Latency: about 1.2 ms) *1
Connectors
INPUT jacks (1–24): XLR type, balanced, phantom power
OUTPUT jacks (1–16): XLR type, balanced
AES/EBU connector: DB-25 type
REAC port: RJ-45 EtherCon type
WORD CLOCK connector: BNC type
REMOTE connector: DB-9 type
COMPUTER port: USB type B
* XLR type: 1 GND, 2 HOT, 3 COLD
* Phantom power: DC +48 V (unloaded maximum), 14 mA (maximum load) (All XLR type inputs)
Power Consumption 62 W
Dimensions
482 (W) x 348 (D) x 177 (H) mm
19 (W) x 13-3/4 (D) x 7 (H) inches
(EIA-4U rack mountable)
Weight
9.7 kg
21 lbs 7 oz
Operation Temperature
+0–+40 degrees Celsius
+32–+104 degrees Fahrenheit
Accessories
Power cord
Owner’s manual
Rubber foot x 4
*1 When a REAC Splitter S-4000D or a switching hub is used in-line with REAC cables, the network latency will increase by the amount of processing delay introduced
by the splitting device itself. The actual delay is dependant upon the specications of the splitting device, though the maximum delay amount for a single splitting
device should be about 200 µs.
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specications and/or appearance of this unit are subject to change without prior notice.
Bekijk gratis de handleiding van Roland S-2416, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
Merk | Roland |
Model | S-2416 |
Categorie | Niet gecategoriseerd |
Taal | Nederlands |
Grootte | 5368 MB |