Handleiding
Je bekijkt pagina 20 van 40
Rinnai 20 GD OIM
CHECK LIST
Please check the following list before calling for Service. Service calls may be charged if faults are caused by
operation errors. Refer to the separate warranty booklet for more details.
If the dryer does not operate at all, check to see if the digital display is ashing with two numbers. If yes, refer to
"Error Codes" on page 21. If no, check the following items:
•
Is the gas supply turned on?
•
Is the electrical plug connected to the power supply and is the power supply switched on?
•
Is electrical power available? Check supply fuses are serviceable.
•
Have the ON/OFF and START/PAUSE buttons been pressed in accordance with these instructions?
•
Is the dryer door properly closed?
•
Is the digital display ashing with two numbers?
If the dryer takes too long to dry or clothing is not drying well, check the following items:
•
Is the CLEAN FILTER indicator illuminated? If yes, clean lters in accordance with instructions on page 18.
•
Ensure items have been through the washing machine spin cycle before loading into the appliance for drying.
•
Ensure garments for drying are not added during operation.
•
Ensure the THICK automatic drying programme has been selected if thick items are being dried.
GENERAL DRYER CHARACTERISTICS
The following characteristics are part of the normal operation of the appliance and do not indicate a fault:
Indication Explanation
The drum is turning even after the nishing signal
has sounded.
Dryer is operating in SOFTEN & COOL mode. Refer to
the section "SOFTEN & COOL Function" on page 11.
There is a delay after pressing the START / PAUSE
button before the OPERATION indicator shows red.
It may take some time before the burner ignites and
combustion starts. This is a normal characteristic,
however if the burner does not ignite at all, contact Rinnai.
Steam is emitted from the discharge duct terminal.
High eciency appliances tend to discharge steam,
especially on cold days. This is normal.
There are some clicking noises after drying rst
starts and after the drying cycle has nished.
This is due to the expansion and contraction of burner
components with heat and is a normal characteristic.
The 'time remaining' shown in the digital display has
not changed for a number of minutes.
During operation when using Automatic Programs, the
control system continually calculates the remaining
drying time based on the rate of drying of the items being
dried. This is a normal characteristic.
SERVICE
NOTE
Faults caused by insucient gas supply, gas quality, installation errors or operation errors are
NOT covered by the Rinnai warranty. Refer to separate warranty booklet for details.
When making a service enquiry, having both the model and serial numbers available, will help our
sta quickly identify your appliance and better attend to your needs.
This information should have been copied to the "Installation Record" on page 34 by your
installer, however if this is not the case, the information can also be found on the data plate located
on the right hand side of the appliance.
This appliance does not contain user serviceable parts and MUST ONLY be serviced and repaired by an authorised
person. Rinnai has a Service and Spare Parts network with personnel who are fully trained and equipped to give
the best service on your Rinnai appliance. If your appliance requires service, please call our National Help Line
(contact numbers for which are on the back cover of this manual).
Rinnai recommends that this appliance be serviced every 2 years.
TROUBLE SHOOTING
Bekijk gratis de handleiding van Rinnai Dry-Soft 9 DRYSOFT9N, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Rinnai |
| Model | Dry-Soft 9 DRYSOFT9N |
| Categorie | Wasdroger |
| Taal | Nederlands |
| Grootte | 5820 MB |
