Rane AC 23S handleiding
Handleiding
Je bekijkt pagina 4 van 18
Manual-1
AC 23S
ACTIVE CROSSOVER
OPERATORS MANUAL
WEAR PARTS: is product contains no wear parts.
MONO 4W OR 5W: INACTIVE 4W: INACTIVE4W: INACTIVE
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
1 00
2
4
8
6
MAXMIN
2
4
8
6
MAXMIN
2
4
8
6
MAXMIN
2
4
8
6
MAXMIN
2
4
8
6
100
80 900
850
150
200
240
750
600
400
190
250
7.0k
5.8k
550
475
350
700
2.0k
2.8k
4.5k
1.0k
190
250
7.0k
5.8k
550
475
350
700
2.0k
2.8k
4.5k
1.0k
1k70
4W: MID / HIGH
2W: INACTIVE 2W: INACTIVE 2W: LOW / HIGH 2W: LOW / HIGH2W: INACTIVE2W: INACTIVE 2W: LOW2W: LOW
100
80 900
850
150
200
240
750
600
400
1k70
MUTE
LEVEL LEVEL LEVEL LEVEL
MASTER
LEVEL
MASTER
LEVEL LEVEL LEVEL
MUTE
FREQUENCY
DELAY DELAY DELAY DELAY
FREQUENCY FREQUENCY
MUTE MUTE
AC 23S
ACTIVE
CROSSOVER
CH 2CH 1
FREQUENCY
LOW MID LOW MIDHIGH HIGH
MIDMONO MASTER SUBWOOFER SUB / LOW HIGHLOW LOW / MID
MID / HIGHLOW / MID MID / HIGHLOW / MID
5W: HIGH-MID / HIGH5W: HIGH-MID5W: MID / HIGH-MID
POWER
QUICK START
Labels above the controls refer to the unit being operated in the
2- or 3-Way Stereo mode. Labels below the controls refer to the
unit being operated in the 4- or 5-Way Mono mode.
Set the STEREO/MONO switch appropriately. e fact that
the AC 23S is a multiple function unit means the outputs are
switched around in Mono mode.
To operate the unit in Stereo 3-Way mode, be sure the rear
panel switches are set for STEREO 3-Way, and the 4W / 5W
switch is set for 5-Way. Following the labels above the controls
and jacks in logical order, you will find Channel 1 Master Input
LEVEL, LOW Output, MID Output, and HIGH Output, with
the same for Channel 2. If you need a summed Mono Low Ou-
put, see ‘Monoing the Low Outputs’ on page Manual-15.
To use the unit as a Mono 5-Way, first check that the Chan-
nel 1 and 2 switches are set to 3-WAY, and the push-switch is
depressed for MONO. Connect the INPUT source to Channel 1
only. Following the labels below the jacks, look at SUB OUT,
then look over at LOW OUT, now go back to MID OUT, then
over to HIGH-MID OUT and then proceed to the HIGH
OUT.
ere are two different configurations for Mono 4-Way
systems. If your LOW / MID can use a crossover frequency
between 70 Hz-1 kHz, see page Manual-7. If your LOW / MID
prefers a higher range of 190 Hz-7 kHz, see page Manual-8.
In agreement with IEC and AES/ANSI standards, AC 23S
wiring convention is pin 2 Positive, pin 3 Negative (return),
pin 1 to chassis ground. See the “Sound System Interconnection”
RaneNote included with this manual for more information on
cabling and grounding requirements.
Bekijk gratis de handleiding van Rane AC 23S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Rane |
| Model | AC 23S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3571 MB |
