Proline 46815 handleiding

Niet gecategoriseerd

Proline

60 pagina's

PDF beschikbaar

Handleiding

17. After detecting any problems in device operation, use the tips included in the table «Troubleshooting guide». If it turns out to be useless, have the jack repaired

by an authorized service center (addresses provided on the warranty card). Damaged jacks cannot be either used or repaired by the user, it is even prohibited. It

does not contain any parts that can replaced by the user (except for possible refilling hydraulic oil).

18. Do not put the jack on its side or upside down (with its base up) (2). The jack should always be operated, stored and transported standing on its base.

SPECIFICATIONS:

Jacks 46802, 46803, 46805, 46808, 46810 (see: Fig. A, p. 2) are not equipped with a carrying handle.

Jacks 46812, 46815, 46820 (see: Fig. A, p. 2) are equipped with a carrying handle (12).

Sound pressure level at workplaces should not exceed 70 dB(A).

CONSTRUCTION:

The jack consists of a hydraulic pump (6), oil reservoir (5), telescopic piston (4), extension screw (11) with saddle (9), base (2). The lever (7) is used to operate the

pump. Its narrower part is used to undo and tighten the release valve (1) of the jack.

In addition, the jack is equipped with a factory adjusted safety valve (3). It is absolutely prohibited for the user to adjust the safety valve.

HOW TO USE IT:

n Preparing for operation:

The lever (7) of the jack consists of two or three main parts. Before you start using the jack, assemble the parts to make the whole lever (see: Fig. D, p. 3). Prior to the

first operation loosen the release valve (1) partly with the lever, but without removing it from the base (2) to avoid oil leakage from the oil reservoir (5), by turning it

counterclockwise (see: Fig. B, p. 2). Then insert the lever into the lever sleeve (8) (see: Fig. D, p. 3) and carry out 6 full vertical pumping cycles (see: Fig. E, p. 3). This is

the best way to provide a correct distribution of hydraulic oil.

n Lifting the vehicle:

The user should make a decision if it is necessary to extend the extension screw (11) to lift the vehicle. To lift your vehicle it may be sufficient to use the very

movement of piston (4). The decision will depend on the vehicle suspension height, on the lifting height needed and should be made by the user after analyzing the

table «Specifications» thoroughly. If the extension screw is necessary, the user should manually undo the extension screw to reach an appropriate height. Then it is

necessary to find an appropriate place of operation for the jack. The base (2) of the jack should rest securely on a hard, level and dry, non-slippery surface, away from

children and animals, in such a way to immobilize the device in a vertical position. The saddle (9) of the jack should be precisely placed under one of the chassis points

designed by the manufacturer to lift the vehicle to provide full stability and should be set centrally on the seat without sliding (before you start lifting read the user's

manual of your vehicle). The vehicle should be protected against the possibility of rolling away or lowering, as it is described in the section entitled «Safety

guidelines».

Using the lever (7) tighten up the release valve (1) completely, turning it clockwise (see: Fig. B, p. 2). Now you can start lifting the vehicle by carrying out vertical

pumping movements of the jack lever (see: Fig. E, p.3). While lifting your vehicle make sure that the car lifting point rests centrally and securely on the jack saddle

and that the base rests securely on the ground. If the saddle is sliding or the jack is shaking, stop lifting the vehicle immediately and start lowering it.

If the jack is overloaded (when the weight of lifted vehicle exceeds the maximum jack capacity), which is strictly prohibited, the safety valve will be triggered,

directing oil back to the oil reservoir (5), thus protecting it against damage. In such situations pumping will not bring any effect.

n What to do in case of failure:

In the case of uncontrolled lowering of the saddle (9), when the release valve (1) is fully shut, stop using the jack and send it to a service center to have it repaired.

n Lowering the vehicle:

If you want to lower the lifted vehicle, use the lever (7) to unscrew the release valve slowly (1), by turning it counterclockwise (see: Fig. B, p.2), making sure not to

remove it from the base (2) to avoid any leakage from the oil reservoir (5).

STORAGE AND MAINTENANCE:

During storage the lever (7) of the jack should be removed from the lever sleeve (8), and the bushing should remain in a horizontal position. The extension screw (11)

should be completely tighten up (hidden in the piston (4) of the jack), whereas the piston should be completely hidden in the oil reservoir (5), i.e. inside the jack

body. It will extend the life of its hydraulic system and reduce the possibility of letting air into the system.

Jack product

code

Maximum

lifting capacity

Minimum saddle

height (9)

Maximum piston

extension (4)

Maximum extension

of extension screw (11)

Maximum saddle

height (9)

Jack weight

46803

46802

46805

46808

46810

46812

46815

46820

2000 kg

3000 kg

5000 kg

8000 kg

10000 kg

12000 kg

15000 kg

20000 kg

168 mm

188 mm

207 mm

222 mm

227 mm

235 mm

100 mm 48 mm 316 mm 2,0 kg

115 mm

125 mm

145 mm

150 mm

60 mm

70 mm

80 mm

60 mm

363 mm

402 mm

447 mm

457 mm

445 mm

2,8 kg

3,7 kg

4,8 kg

6,0 kg

7,0 kg

8,6 kg

Bekijk gratis de handleiding van Proline 46815, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.