Practixx PX-BTS-370 handleiding
Handleiding
Je bekijkt pagina 25 van 48
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such precautionary measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools and attachments. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use electric tools, insertion tools, etc. according
to these instructions. Take into account the
working conditions and the work to be per-
formed. Use of the power tool for operations differ-
ent from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe han-
dling and control of the tool in unexpected situa-
tions.
5.5 Service
a) Only have your power tool repaired by qualified
specialists and only with original spare parts.
This will ensure that the safety of the power tool is
maintained.
5.6 Additional safety instructions for
the belt and disc sander
WARNING
Do not use your product until it is completely assem-
bled and installed according to the instructions.
ATTENTION
This product is designed for sanding wood or wood-
like material only. The sanding of other materials can
cause fire, injuries, or damage the product.
ATTENTION
Only assemble and use the product on a horizontal
surface. A non-horizontal surface can damage the
motor.
• Read the entire operating manual before using the
product.
• Always wear safety goggles.
• This product may only be operated indoors.
• If the product tends to tilt or walk, especially when
sanding long and heavy panels, it must be fastened
to a solid surface of sufficient carrying force.
• Make sure the sanding belt runs in the correct direc-
tion. See arrows at the back of the sanding belt.
• Make sure the sanding belt is running correctly so
that it cannot come off the drive pulleys.
• Make sure the sanding belt is not twisted or loose.
• Firmly hold the workpiece when sanding.
• Always use the stop when using the belt and disc
sander in horizontal position.
• Always hold the workpiece firmly to the table when
using the belt and disc sander.
• Always hold the workpiece to the side of the sand-
ing disc running downwards, in order to maintain
the workpiece pressed to the table. By using the up-
ward-running side of the sanding disc, the work-
piece could be ejected and cause injury to you or
other persons.
• Always keep a minimum distance of about 2 mm or
less between the table or stop and the sanding belt
or disc.
• Do not wear protective gloves. Do not hold the
workpiece with a cloth during sanding.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt or
disc.
• When sanding a large piece of material, provide an
additional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the stop. Exceptions are
the sanding of curved workpieces on the outside of
the sanding disc.
• Always clear the table, fence or sanding belt of
scraps or other objects, before turning the product
on.
• Do not perform any layout assembly or set-up work
on the table while the product is in operation.
• Switch the product off and pull the power plug from
the socket when fitting or removing accessories.
• Never leave the working area of the product while
the product is running, or as long as it has not come
to an absolute standstill.
• Always place the workpiece on the sanding table or
position it firmly against the sanding stop. Place
curved workpieces securely on the table when
sanding on the sanding wheel.
• Always ensure that the belt and disc sander are sta-
ble and secured (e.g. fastened to a workbench).
• Before each use, check the sanding disc and sand-
ing belt for damage.
GB | 25www.practixx.com
Bekijk gratis de handleiding van Practixx PX-BTS-370, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Practixx |
| Model | PX-BTS-370 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6461 MB |
