Parkside PGS 500 C2 handleiding
Handleiding
Je bekijkt pagina 10 van 48
GB / CY
│
7
If, for example, a grinding disc catches or
jams, the edge of the grinding disc that
is projecting into the workpiece can get
caught and break o the grinding disc or
cause a kickback. The grinding disc may
then jerk violently towards or away from the
operator, depending on the rotation direc-
tion of the disc at the blockage. This can
also cause the grinding discs to break.
A kickback is caused by improper or in-
correct use of the power tool. This can be
avoided by taking proper precautions as
described below.
a) Hold the power tool rmly in both
hands and position your body and
arms so they can absorb the force of
a kickback. By taking adequate precau-
tions, the operator can stay in control of
the kickback forces.
b) Take special care when working near
corners, sharp edges, etc. Do not
allow the accessory tool to bounce
back from the workpiece or jam. The
rotating accessory tool is more likely to
jam in corners or sharp edges or if it re-
bounds o them. This can cause a loss
of control or kickback.
c) Do not use toothed saw blades. These
kinds of accessories often cause a kick-
back or loss of control over the power
tool.
d) Always move the accessory tool into
the material in the same direction in
which the cutting edge leaves the
material (in other words, the same
direction in which the dust/chips are
ejected). Guiding the power tool in the
wrong direction will cause the cutting
edge of the accessory tool to jump out
of the workpiece, which can lead to the
accessory tool being pulled in this direc-
tion.
Supplementary safety instructions
for grinding
Special safety instructions for grinding
a) Use only the grinding accessories
approved for your power tool and only
for the recommended applications.
For instance, never grind with the side
surface of a cutting disc. Cutting discs
are designed to remove material with the
edge of the disc. Any lateral application
of force on these grinding tools can
cause them to break.
b) For conical and pencil grinders, use
only undamaged mandrels of the
correct size and length and without
an undercut on the shoulder. Using an
appropriate mandrel re duces the risk of
breakages.
c) Always clamp the workpiece when
using rotary les, cutting discs, high-
speed milling tools or hard-metal mill-
ing tools. Even minimal tilting in the
groove can cause these tools to jam
and lead to a kickback. When a cut-
ting disc jams, it usually breaks. When
a rotary le, high-speed milling tool or
hard-metal milling tool jams, the acces-
sory tool can jump out of the groove and
lead to loss of control of the power tool.
Additional safety and working
instructions
■ Always wear protective goggles when
working with the machine.
■ We recommend using protective gloves,
sturdy and non-slip footwear and an
apron.
■ Remove the plug from the mains socket
before making any adjustments to the
machine.
■ Do not connect the machine to the
mains socket unless it is switched o.
■ Always keep the power cable out of the
operating area of the machine. Always
route the cable away from the machine
towards the rear.
IB_458746_PGS500C2_LB7_CY.indb 7IB_458746_PGS500C2_LB7_CY.indb 7 18.07.2024 13:37:5718.07.2024 13:37:57
Bekijk gratis de handleiding van Parkside PGS 500 C2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Parkside |
| Model | PGS 500 C2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5180 MB |
