Parkside PDFW 120 B3 handleiding
Handleiding
Je bekijkt pagina 17 van 86
15GB/IE/NI/CY
Catching or jamming leads to an abrupt stop of
the rotating accessory tool. If this happens, an
uncontrolled power tool will turn rapidly against
the direction of rotation of the accessory tool.
If, for example, a grinding disc catches or jams,
the edge of the grinding disc that is projecting
into the workpiece can get caught and break
off the grinding disc or cause a kickback. The
grinding disc can then fly in the direction of the
operator or away from him, depending on the
direction of rotation of the disc at the blockage.
This can also break grinding discs.
A kickback is caused by incorrect use or misuse
of the power tool. This can be avoided by
taking proper precautions as described below.
a) Hold the power tool firmly in both
hands and position your body and
arms so they can absorb the force
of a kickback. By taking adequate
precautions, the operator can stay in
control of the kickback forces.
b) Take special care when working
around corners, sharp edges,
etc. Avoid allowing the accessory
tool to bounce back from
the workpiece or jam in the
workpiece. The rotating accessory tool
is more likely to jam in corners or sharp
edges or if it rebounds off them. This can
cause a loss of control or kickback.
c) Do not use toothed saw
blades. Such accessories often cause a
kickback or loss of control over the power
tool.
d) Always move the accessory tool in
the same direction in the material
in which the cutting edge leaves
the material (in other words, the
same direction in which the dust
is thrown out). Guiding the power
tool in the wrong direction will cause the
cutting edge of the accessory tool to jump
out of the workpiece which can lead to the
accessory tool being pulled in this direction.
e) Always fix the workpiece when
using rotary files, cutting discs,
high-speed milling tools or hard-
metal tools. Even a minimal tilting in
the groove can cause these tools to jam
and lead to a kickback. When the cutting
disc jams, it usually breaks. When a rotary
file, high-speed milling tool or hard-metal
milling tool jams, the accessory tool can
jump out of the groove and lead to loss of
control of the power tool.
Supplementary safety
instructions for grinding and
abrasive cutting
Special safety instructions for grinding
and abrasive cutting
a) Use only the grinding accessories
approved for your power tool
and only for the recommended
applications. Example: Never
grind with the side surface of a
cutting disc. Cutting discs are designed
to remove material with the edge of the
disc. Any lateral application of force on
these grinding tools can lead to breakage.
b) Use only undamaged mandrels
of the correct size and length and
without undercut on the shoulder
for conical and straight pencil
grinders. Using an appropriate mandrel
reduces the risk of breakages.
c) Avoid cutting disc jams or
excessive contact pressure. Do
not make any excessively deep
cuts. Overloading the cutting disc
increases the stress and likelihood of tilting
or blocking and thus the possibility of a
setback or a breakage of the grinding tool.
d) Avoid putting your hand in the
area in fron of or behind the
rotating cutting disc. When you move
the cutting disc away from your hand, it is
possible, in the event of a kickback, that
the power tool along with the rotating disc
could be thrown out directly towards you
along with the rotating disc.
Bekijk gratis de handleiding van Parkside PDFW 120 B3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Parkside |
| Model | PDFW 120 B3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9931 MB |
