Panduit VS2-AVT-3PF-08 handleiding
Handleiding
Je bekijkt pagina 18 van 20
1002985, B21110_EN_rev4 18 10/06/2022
Maintenance
WARNING:
The battery powered indicator module contains a lithium battery that is a fire, explosion and severe burn hazard. Do not
crush, recharge, disassemble or heat above 85°C (185°F), incinerate, or expose contents to water.
The AVT will not work with a standard alkaline 1.5 V AA battery. Use only Panduit approved battery.
Battery, system cable, o-rings and gaskets can be replaced. No other part of the product is serviceable.
Do not attempt to open the indicator module or isolation module for repair or modification. When servicing this product,
only use specified replacement parts.
The o-rings and gaskets can be replaced if they become dry or brittle. In critical sealing applications, such as wash down
environments, it is recommended that the o-rings and gaskets be replaced every 5 years. Apply a light coating of silicone
grease to the o-rings to promote sealing and extend o-ring life.
Special Conditions
of Use
Hazardous Locations
Refer to Page 2 of this manual for all Special Conditions of Use for Hazardous Locations.
VISUAL INSPECTION
Periodically inspect the AVT and replace any damaged parts, cables or terminations.
Inspect the sensor lead terminations to ensure they are tight, the leads are secure, and does not show signs of damage.
Inspect the system cable to ensure it is locked into place on both ends, is secure and does not show signs of damage.
Inspect the indicator module to ensure o-rings or gaskets are not dry or brittle.
Inspect the indicator module to ensure the retention nut is tight and cap is firmly in place.
CLEANING INSTRUCTIONS
The indicator module can be cleaned with a damp cloth or isopropyl alcohol based cleaner. Do not use abrasives or high alka-
line cleaners. Do not leave cleaners on the device for a long period, rinse immediately. Do not apply cleaners in direct sunlight
or elevated temperatures.
Before a wash down operation, ensure the o-rings and gaskets are in good condition, the faceplate is not damaged and fully
secured to the unit, and the cap is fully installed.
BATTERY REPLACEMENT
Follow the steps below to replace the battery. The table below provides the list of batteries approved for use with the
AVT. Do not discard the battery in the trash; take it to an appropriate battery recycling facility.
Panduit Part No. Manufacturer Mfr. Model No. Size Description Operating Temperature
VS-AVT-BATTERY Titus ER14505M ER14505
3.6 Volt
Lithium Battery
-25°C to 60°C (-13°F to 140°F)
1. Twist the
indicator module
cap coun-
terclockwise
approximately
90 degrees, until
you feel a stop.
2. Grip the battery
tray and slide it
out until you feel a
stop. The battery
tray is not intended
to be fully re-
moved.
3. Remove used
battery. Install a
new battery. En-
sure the battery is
fully seated before
proceeding.
4. Slide the battery tray
back in the housing.
A self test is initiated
when the battery
tray is inserted and
connection is made
between the battery
and AVT electronics.
5. Replace the cap.
Twist cap clockwise
to lock into place.
6. Record the date the battery was replaced in equipment documentation.
Bekijk gratis de handleiding van Panduit VS2-AVT-3PF-08, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panduit |
| Model | VS2-AVT-3PF-08 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4742 MB |
