Handleiding
Je bekijkt pagina 21 van 297
English - 20 -
Make sure your soundbar is switched on and the
volume is up then press Select.
Press Standby on your TV remote control, wait 10
seconds then press the Standby button again.
You'll now be asked ‘Did your soundbar turn o and
then back on when you pressed Standby’. If it did
highlight Yes and press Select, if it didn't highlight
No and press Select. You may need to repeat this
process multiple times.
When your soundbar eventually turns o and on, you
will be asked to press the volume up and down buttons.
Press the Volume + and - buttons.
If your volume level adjusted as expected highlight Yes
and press Select. If not select No and continue until
the volume level changes.
Your Fire TV remote has now been setup, it will
now switch your soundbar on and o and adjust the
volume level.
Now when you switch your TV on your soundbar will
also switch on. The TV speakers will be automatically
switched o.
Soundbar/Receiver Settings
Once you have setup your soundbar or receiver you
will now see either Soundbar or Receiver in the
Equipment Control menu. This will show you all the
settings for your device.
Highlight Soundbar or Receiver and press Select.
You will now see a list of settings.
Highlight the setting that you wish to adjust and press
Select.
Volume Increments: Set the amount the volume
increases or decreases when you ask Alexa to change
the volume. The default increment is set to 4.
Press Fast Forward or Rewind to increase or
decrease the increments. Press Option to restore
back to default settings.
Infrared Options: Changes the infrared options.
IR Prole, Timing and Repetition options will be
available.
Power Controls: Adjusts the power on/o settings
for your soundbar or receiver. Power On Delay and
Power Control options may be available.
Fire TV Input: Change the input, to which your
soundbar or receiver will switch to for watching Fire TV.
Change Soundbar/Change Receiver: If you
would like to change the soundbar or receiver that’s
connected to your TV highlight Change Soundbar/
Change Receiver and press Select. To remove the
device highlight Change Soundbar/Change Receiver
and press the Option button.
Restore Soundbar Defaults/Restore Receiver
Defaults: Restores all the settings that you may have
changed back to factory defaults. This option will be
available if you change the default settings.
Advanced Settings
Adjust the power timing if your soundbar or receiver
does not switch on/o.
Press Fast Forward or Rewind to increase or de
-
crease the increments.
Press Option to restore back to default settings.
Live TV
This menu allows you to tune in your TV, manage the
channels, set up a CI card and set parental controls.
Highlight Live TV and press Select.
Channel Scan
You should have already tuned in your TV during the
initial setup process. But if you skipped the channel
scan step or if you need to retune your TV follow these
instructions.
Highlight Channel Scan and press Select.
You will be prompted to check that your antenna is
set up and that the cable is plugged properly into
the antenna input socket on your TV. Press Select
to proceed.
Select your scanning preference to install channels.
Satellite, Terrestrial and Cable options will be
available.
If the Terrestrial option is selected, the TV will search
for digital terrestrial broadcasts. Select the search
method on the next screen and press Select to start
the search. If you continue with the manual scan, you
will need to congure the Frequency and UHF Band
options before starting the scan.
If the Cable option is selected, the TV will search for
digital cable broadcasts. On the next screen, select the
cable provider, if any available, or the search method,
then press Select to start the search. You may need
to congure the Network ID and Frequency options
before starting the scan.
If the Satellite option is selected, you can choose an
operator on the next step, if any available. You can
also choose to perform complete or manual scan.
Highlight the option you prefer and press Select button
to proceed. If you continue with manual or complete
scan option, you will have to select the satellite in
the next step. Then the Satellite Connection screen
will be displayed next. You can set the LNB Type,
LNB Power, DiSEqC Version, Port, Single Cable,
ToneBurst, Frequency, Polarisation, Symbol Rate
and Scan Mode parameters of the selected satellite
corresponding to your environment on this screen.
Depending on your previous selections, some options
may not be available or may be set automatically.
Change if necessary and proceed.
Bekijk gratis de handleiding van Panasonic TV-65W83AE8, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panasonic |
| Model | TV-65W83AE8 |
| Categorie | Televisie |
| Taal | Nederlands |
| Grootte | 40063 MB |
