Handleiding
Je bekijkt pagina 7 van 20
1 Standardized flexible tube for gas
with a length of 0.5m.
2 Collar-clips with screw for the
flexible tube (fig.1).
In order to identify these elements,
check the type plate and contact
your gas distributor.
A flexible tube and a pressure
regulator must be used for the
connection of this device. Contact
your gas distributor.
Working description
Depending on the model, your
space heater may be fitted with the
following elements:
1 – Key to start-up, light and select
the power of the device.
2 – Protective screen guard.
3 – Blue flame burner.
4 – Pilot light window.
5 – Back panel.
6 – Fitting lugs for back panel.
7 – Gas feed coupling.
8 – Wheels for transport.
Heater start-up
Once the space heater has been
taken out of its packaging:
Remove the back panel form the
device.
Connect the flexible tube to the gas
inlet coupling of the space heater
and to the regulator, ensuring a
gastight fit with the collar-clips well
screwed down. Avoid twisting the
flexible tube.
Place the gas cylinder on the base of
the space heater and fit the
regulator to the cylinder. After
opening the regulator, check that
there are no gas leaks by applying
soapy water with a paintbrush to
the union of the flexible tube with
the space heater and the regulator.
Fit the back panel using the
attached fixing lugs (fig.3).
CAUTION: For their own safety,
keep the package (cardboard,
Styrofoam, plastic bags, etc.) away
from your children.
Note: the replacement of the
cylinder should be carried out in a
non-flammable environment.
The space heater includes a safety
device, which turns the device off an
«d extinguishes the pilot flame in
the ventilation in the premises is
insufficient or the concentration of
CO2 exceeds the maximum
stipulated by law.
It is usual for this device to operate
in very small premises.
If the flame does go out, ventilate
the room well and wait a few
minutes before reigniting the space
heater.
Ignition instructions
Attention: before using the space
heater for the first time and after
long periods of non-use, we
recommend switching on the
control buttons several times
alternately and without gas flow in
order to facilitate its operation.
The space heater can be regulated
to two different heat intensities:
MAXIMUM and MINIMUM. The
ignition mechanism is piezo-
operated.
Open the gas outlet by rotating the
lever on the regulator to the correct
position (fig.2).
Turning on the space heater
Press the button and rotate it to
your left, holding it down for 20
seconds. Repeat this procedure
several times, if necessary, until the
pilot light ignites near the bottom
part of the protective screen guard
(where the spark is seen), fig.4 and
keep pressing the button for 10
seconds, then rotate the button to
maximum position to ignite the
burners. If, on releasing the button,
the flame goes out, please repeat
the whole procedure.
For MINIMUM heat – rotate the
button to
For MAXIMUM heat – rotate the
button to
Maintenance
If any anomaly is observed or spare
parts are required, contact our
Technical Service.
The periodical maintenance must be
carried out exclusively by an
authorized technician.
We would recommend that you
have a service carried out every two
years by an authorized technician.
Watch the pilot light, which should
be stable.
Check to see if it is necessary to
change the flexible gas tube. If it
proves necessary, obtain a new tube
and connect it as explained in
“Heater start-up”.
It is recommended that the cleaning
of the space heater be carried out
with the gas regulator closed and
the heater completely cold, with
nonabrasive products.
The user must wear protective
gloves to clean the heater.
When the space heater is not in use,
we recommend storing it in a dust-
free atmosphere, protected with a
cloth or plastic cover in a dry place.
Warranty
All our space heaters have been
meticulously checked before leaving
the factory. Nevertheless, if any
anomaly is observed remember that
our extensive Technical Service
Bekijk gratis de handleiding van Orbegozo HBF 50, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Orbegozo |
| Model | HBF 50 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 2404 MB |
