Optex SIP-5030-IP-BOX handleiding

Handleiding

123456789101112/ 12

Afdrukken

Je bekijkt pagina 4 van 12

- 4 -

- 5 -

Mounting tips>>

Engage the convex section of the area viewnder xing

arms with the notches of the main unit, and insert and

mount the arms.

Alarm Creep

Mount the area plate so that an arrow of the plate

center section faces upward and the letter surface can

be seen.

Insert the area plate into the top and bottom grooves of

the area viewnder until the plate is stopped by the ribs.

SIP-5030

F2

F3

F4

F5

E2

E3

E4

E5

D

1

D

2

D3

D4

D

5

D6

C1

C2

C3

C4

C5

C6

B1

B2

B3

B4

B5

7

8

9

10

1

2

3 4

5

6

F1

F6

E1

E6

B6

5030

(521206)

SIP-100

E1

D1D2

E2

F1 F2

C1 C2

B1 B2

2

1

100 (521207)

Fine adjust the main unit angle in vertical and horizontal

direction by observing the target area through the area

viewfinder.

3 Locate the center circle of the area

plate on the center circle of the lens

of the area viewnder, and check the

detection area pattern on the area

plate and the background image.

* Each letter on the area plate

corresponds to each mirror number

(see Step 8-2).

* You cannot observe mirror

numbers B1 to F1 and B6 to F6

(shown at right) of the SIP-5030

area plate through the inspection

window. Check them using the

walk tester.

Adjusting tips>>

If you experience any of the following, see Step 10.

F2

F3

F4

F5

E2

E3

E4

E5

D

1

D

2

D3

D4

D

5

D

6

C1

C2

C3

C4

C5

C6

B1

B2

B3

B4

B5

7

8

9

10

1

2

3 4

5

6

F1

F6

E1

E6

B6

5030

(521206

)

F2

F3

F4

F5

E2

E3

E4

E5

D1

D2

D3

D4

D

5

D6

C1

C2

C3

C4

C5

C6

B1

B2

B3

B4

B5

7

8

9

10

1

2

3

4

5

6

F1

F6

E1

E6

B6

5030

(521206)

•

•

•

(5)

Cautions>>

The area viewnder is a supporting tool for detection

area adjustment.

After you have adjusted the detection area using the

area viewnder, always check the area using the walk

tester.

Never look directly into the sun through the area

view nder.

After you have used the area viewnder, store it away

from direct sunlight.

Securely tighten the adjustment screw that you have

loosened.

Connect the walk tester (optional) to the sensor unit, and

check that the detection area is correct.

REDWAVE

REDWAVE

MICROWAVE

REDWAVE

ALARM OUTPUT

CELL BATTERY

POWER

SUPPLY

FROM

SENSOR

POWER OFF

REDWAVE

PIR NEAR

REDWAVE

PIR FAR

MEGARED

FAR

MEGARED

NEAR

REDWALL

REDWIDE

WALKTESTER

REDWALL

REDWIDE

MEGARED

CONNECTION

SELECT

SWITCH

MODE

SELECT

SWITCH

POWER

SELECT

SWITCH

OPM-WT

1 When the power selector switch is turned to “POWER

SUPPLY FROM SENSOR” position after plugging

the cable into the walk tester connector, a continuous

beeping sound will be heard.

2 When a pedestrian first enters the detection area, the

strong and weak beeps will sound alternately.

3 When the entirety of a pedestrian’s body is detected, the

strong beep will sound continuously.

•

•

•

•

(6)

(7)

Fixing arms

Notch

Convex

section

Grooves

Ribs

Arrow

marking

1 To change the direction of the inspection

window, rotate the area viewnder in a

horizontal direction until it clicks and stops.

2 Move your face close to the viewnder

so that your eye comes within 5 mm of

the inspection window (lens surface).

For near area alarm output

For far area alarm output

Use at “REDWAVE ALARM

OUTPUT” position to

conrm far and near area

alarm output.

Power selector

switch

Use at “REDWALL” position.

For creep zone alarm output

F

2

F3

F4

F5

E2

E3

E4

E

5

D

1

1

D

2

D3

3

D4

4

D

5

D

6

6

C

1

C2

C3

C4

4

C

5

C6

1

B

2

B3

B4

B5

7

8

9

10

1

2

3

4

5

6

F1

F6

E1

E6

B

5030

(

521206

)

6

B6

6

B

B

B1

E

E

1

1

Center circle of the lens

Center circle of the

area plate

The detection area is

inside the frame

border.

Invisible area

The sensor area is extended

over the street where a person

walks or a car drives.

Branches of a tree and grass

move when the wind blows.

Limit line of

detection area

SIP5030_EN.indd 4 2009/03/18 9:28:31

123456789101112/ 12

Bekijk gratis de handleiding van Optex SIP-5030-IP-BOX, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Optex (Niet gecategoriseerd)

Handleiding bekijken

Optex TI-S

Niet gecategoriseerd - handleiding

Handleiding bekijken

Optex SL-650QDP

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd