Olimpia Splendid Bi2 SL SMART S1 handleiding

Niet gecategoriseerd

Olimpia Splendid

164 pagina's

PDF beschikbaar

Handleiding

EN - 44

ENGLISH

2.7.2 - Connections

Thechoiceandsizingofthehydrauliclinesmustbemadebyanexpertwhomustoperateaccordingto

therulesofgoodtechniqueandthelawsinforce.

Tomaketheconnections:

- position the hydraulic lines

- tightentheconnectionsusingthe“spannerandcounterspanner”method(g.12ref.B)

- checkforanyleaksofliquid

- coattheconnectionswithinsulatingmaterial(g.12ref.C).

The hydraulic lines and joints must be thermally insulated.

Avoid partially insulating the pipes.

Do not over-tighten to avoid damaging the insulation.

Usehempandgreenpastetosealthethreadedconnections;theuseofTeonisadvisedwhenthereis

anti-freeze in the hydraulic circuit.

2.8 - CONDENSATION DISCHARGE

Thecondensationdischargenetworkmustbesuitablysized(minimuminsidepipediameter16mm)and

thepipelinepositionedsothatitkeepsaconstantinclination,neverlessthan1%.Intheverticalinstal-

lation,thedischargepipeisconnecteddirectlytothedischargetray,positionedatthebottomoftheside

shoulderunderneaththehydraulicxtures.Inahorizontalinstallationthedischargetubeisconnectedto

the one already present on the machine.

ForinstallationoftheSLversionsinahorizontalposition,horizontalcondensationcollectionbasin

accessorykitsareavailableSL.

- Ifpossible,makethecondensationliquidowdirectlyinagutterora“rainwater”discharge.

- Whendischargingdirectlyintothemaindrains,itisadvisabletomakeasiphontopreventbadsmells

 returningupthepipetowardstheroom.Thecurveofthesiphonmustbelowerthanthecondensation

 collectionbowl.

- Ifthecondensationneedstobedischargedintoacontainer,itmustbeopentotheatmosphereandthe

 tubemustnotbeimmergedinwatertoavoidproblemsofadhesivenessandcounter-pressurethatwould

 interferewiththenormaloutow.

- Ifthereisaheightdi󰀨erencethatcouldinterferewiththeoutowofthecondensation,apumpmustbe

 mounted(accessorykit):

- in a vertical installation mount the pump under the lateral drainage tray;

 -inahorizontalinstallationthepumppositionmustbedecidedaccordingtothespecicrequirements.

Inanycase,consultthespecicinstructionsinthecondensationdischargepumpkit.

However, on completion of the installation it is advisable to check the correct outow of the

condensation liquid by slowly pouring about ½ l of water into the collection tray in about 5-10

minutes.

2.8.1 - Mounting the condensation discharge device in the vertical version

Connecttothecondensationcollectiontraydischargeunion(g.13ref.A)apipefortheoutowofthe

liquid(g.13ref.B)blockingitadequately.Checkthatthedrip-collectorextension(g.13ref.C)ispresent

and correctly installed.

2.8.2 - Mounting the condensation discharge device in the horizontal version

TomountthehorizontalbowlontheSLversionsrefertotheinstructionsintherelativeoptionalkit.

- Belowthesidecorrespondingtothecondensatedraintubeoutlet,cutthepre-cutarea(g.14ref.A).

- Retthesidepanel.

Bekijk gratis de handleiding van Olimpia Splendid Bi2 SL SMART S1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.