Nord Stage 4 handleiding
Handleiding
Je bekijkt pagina 46 van 76
46 | NORD STAGE 4 USER MANUAL OS V1.4X
EXTERN PARAMETERS
The most frequently used Extern parameters are controlled from the
Synth display, using its three dials:
MIDI CC
The two CC VAL controls makes it possible to transmit MIDI Control
Change messages for controlling parameters of your choice on the
external instrument. The left and middle Synth display dials control the
values of the sent CC messages.
First, the controller numbers to transmit needs to be defined within the
Extern Menu:
1 Enter the EXTERN menu (Shift+Program 8).
2 Use the PAGE 3/4 buttons to select the Extern Settings “CC
Number 1/2” menu page.
3 Use the Num1 and Num2 soft buttons to select the first and
second CC number respectively.
4 Use the PROGRAM Dial to select a MIDI CC Number (0-119). Refer
to the manual for the external unit to see which parameters are
assigned to which CC numbers.
5 To determine the initial values for each CC number when the
program is loaded, use the CC VAL dials under the Synth display
and select an appropriate value.
6 Press EXIT (Shift) to leave the menu.
The external instrument or unit may have to be manually set to receive
MIDI CC messages for this to work as expected.
PROGRAM
The PROGRAM dial allows for selecting programs in the external
instrument, by sending Program Change messages. Note that the
external instrument may also have to be set to receive MIDI Program
Change messages.
! The Stage 4 itself can transmit MIDI Program Change when you
select a Program. If this occurs on the same MIDI channel, it can
lead to unwanted results on the external units. Make sure that the
Global MIDI channel is not the same as the Extern MIDI channel.
Settings related to Program Change on the Global MIDI channel
are found in the MIDI menu, see page 59.
If the external instrument organizes programs in Banks, there is an
option to send Bank Select messages, which can be defined in the
Extern Menu page, see “Extern Menu” on page 61.
SEND ON LOAD
Often, it will be desirable to send certain MIDI data instantly when a
program is loaded on the Nord Stage 4. This allows for an external unit
to switch program, or reset a CC value in sync with program changes
on the Nord Stage 4.
VOLUME
In Extern mode the Layer fader will send MIDI Volume CC7 messages
(0-127). This allows for controlling the volume level of the external
device. The external unit must be set to receive MIDI CC messages for
this to work as expected.
ARPEGGIATOR
The Synth Section ARPEGGIATOR can also be used in Extern Mode. All
the Arpeggiator controls, including Pattern, can be used for generating
outgoing MIDI, but note that the Gate setting has no effect in Extern
mode.
EXTERN SECTION AND MIDI ECHOING
When an external device transmits MIDI notes to the Stage 4 global
channel and the Extern section is active, incoming MIDI notes can be
re-routed to the MIDI Output of the Stage 4, on the active Extern MIDI
channels.
This allows you to control one external device from another external
device. The incoming notes must be on the same MIDI channel as set in
the Stage 4 for the Global MIDI channel.
l The Extern menu setting for “Echo Global To Extern Channel” must
in these cases be set to “On”.
OTHER EXTERN MENU SETTINGS
There are additional menu settings for the Extern Mode, that have not
been covered in this chapter. Refer to the Menu chapter, on page 61,
for further information on those.
EXTERN
CC VAL 1 CC VAL 2
1
PROGRAM
77 12
Bekijk gratis de handleiding van Nord Stage 4, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Nord |
| Model | Stage 4 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10906 MB |
