Nord Stage 4 handleiding
Handleiding
Je bekijkt pagina 38 van 76
38 | NORD STAGE 4 USER MANUAL OS V1.4X
The following parameters are available as Morph destinations:
Organ Piano Synth Effects
Layer Level Layer Level Layer Level Mod 1 Rate
Drawbars LFO Rate Mod 1 Amt
Rotary speed Osc Ctrl Mod 2 Amt
LFO Amount Delay Tempo
Filter Freq Delay Feedback
Filter Resonance Delay Dry/Wet
Arp/Gate Rate EQ Mid / Filter Freq
Drive Amount
Reverb Dry/Wet
l Double-tapping a Morph Assign button activates morph assign
latch mode, allowing for assigning morphs without keeping that
button pressed down. Press EXIT to leave latch mode.
l Morphs can be copied from one control source to another, see
page 42.
MORPH INDICATORS
All morphable parameters are equipped with some means of showing
that a morph has been assigned to it, or that a morph is being
performed. These are the three different types of indications used:
LED FADERS
The level controls of the Organ, Piano and Synth Layers feature a
physical fader and an LED graph. These provide a clear indication of the
morph start and end points as the morph is set up, and allow the control
to display its current value at all times as a morph is being performed.
MORPH LEDS
Most morphable parameters are equipped with a
“morph LED” which will be lit with a green light after a
morph source has been assigned to the parameter.
DRAWBAR LEDS
If a drawbar has been selected as a morph destination, the drawbar
LEDs will adjust accordingly as a morph is being performed.
i Note that morphs are not applicable in Drawbar Live mode.
CLEARING A MORPH
Hold SHIFT and press a MORPH ASSIGN button to CLEAR all Morphs
for this source – for all Layers. To clear a particular assignment, hold
the Morph Assign button and operate the control to remove the “gap”
between the stored setting and the Morph setting.
SPLIT
The Nord Stage 4 keyboard can be split in up to four
keyboard zones; 1, 2, 3 and 4, separated by the three
available split points, Low (L), Mid (M) and High (H). Any
Organ, Piano or Synth Layer can then be freely assigned
to any or all of these zones.
A single press of the Split ON/SET button will turn the split function on
or off. Pressing and holding the button, as indicated by the “6“ symbol,
will open the Keyboard Split screen in the display.
Pressing SHIFT and SET KEY shifts the position of the currently selected
split point.
KEYBOARD SPLIT SETTINGS
After a split has been activated, use the KB ZONE controls (accessed
with SHIFT) below each sections Octave Shift buttons to assign a Layer
to one or more zones. The four Zone LEDs indicate which zone(s) each
Layer is assigned to.
CHOOSING A SPLIT POSITION
The Keyboard Split page – accessed by holding down the Split SET 6
button – allows for assigning each of the three split points to a keyboard
position, or for deactivating a split point by pressing its corresponding
soft button. There are 11 possible keyboard split positions, ranging from
C2 to C7. To adjust a split point, make sure the Note row is focused by
using the 6/5 soft button (PROGRAM 1 button) and then select the
split point by pressing its corresponding soft button (Low, Mid or High),
corresponding to the PROGRAM 2-4 buttons, and turn the dial.
The LEDs located between the keyboard and the panel controls indicate
which split positions are active at all times.
SPLIT XFADE SETTINGS
Normally the transition between two keyboard zones is immediate, with
no overlap between the sounds selected for each zone. By adjusting the
xFade setting for a split point, the sounds can instead be “cross-faded”
across the split point, giving a smoother transition between the sounds.
To adjust Split xFade, make sure the xFade row is focused by pressing
the 6/5 soft button (PROGRAM 1 button).
Select the split point to adjust by pressing its soft button (Low, Mid or
High) and turn the dial to change its setting.
With the – setting no cross-fade is applied.
The ±6 setting represents a width of 6 semitones on each side of the
split point, meaning that the sound below the split point will reach 6
notes above it, after which it will be completely faded out. Sounds above
the split point will similarily reach 6 notes below it.
The ±12 setting provides a width of 12 semitones below the split point
and 12 above it.
MST CLK
The Master Clock lets you synchronize the Arpeggiator/Gate, the Synth
LFO, the Delay and Mod 1 Rate on the Nord Stage 4. Not only can
these be made to run in sync with each other; different subdivisions
can be set for all synced components, allowing for some great rhythmic
effects.
Tap the TAP/SET button a minimum of four times to set a tempo,
expressed in BPM (beats per minute). Keep tapping the button to further
refine the tempo setting if needed.
KEYBOARD SPLIT
-
C4
MidLow High
xFade
Note
-
Off
Off
±12
Bekijk gratis de handleiding van Nord Stage 4, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Nord |
| Model | Stage 4 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10906 MB |
