Handleiding
Je bekijkt pagina 17 van 161
Wiring Diagram 90-082:
Assembling Instructions
Extract the heater from its carton. If the unit is anyhow damaged, do
not use it and contact your dealer.
90-080: the heater is only need to fix the plastic handle, no further
operations required
Pos.
Description
Qty
A
Screw
2
B
Plain washer
2
C
Handle
1
90-081; 90-082: The following accessories are supplied in the
shipping carton.
Pos.
Description
Qty
A
Handle
1
B
Screw
6or8
C
Spring washer
6or8
D
Plain washer
6or8
E
Feet pipe
1
F
Nut M5
6or8
G
Nut M12
2
H
Plain washer ø12
2
I
Wheel
2
J
Wheel shaft
1
K
Cotter
2
To assemble the heater, proceed as follows:
1. Insert the wheel shaft J to the corresponding hole of
feet pipe E，insert the cotter K to the corresponding holes; put plain
washer H to the two sides of shaft, slide the wheel I over the wheel
shaft J，screw the nut G to fix the wheel on the shaft.
2. Put the heater body on the feet pipe assembly, make
sure the 4 holes of handle A point towards the corresponding 4 holes
on the feet pipe respectively.
3. Using the screw B ,spring washer C, plain washer D
and nut 4 to fix the feet pipe assembly and handle to the tank.
5. Installation Instructions
Position the heater on a flat, level, non-flammable, solid surface.
Direct-fired heaters are intended for use in outdoor open areas or in
indoor well ventilated areas. For indoor use, provide permanent
ventilation openings of at least 25 cm²/kW, equally distributed
between floor and high level, with a minimum of 250 cm².
90-080
90-081
90-082
Min.
opening size
320cm3
450cm3
750cm3
•Only install the heater in normal upright position.
•Do not place the heater near walls, corners or low ceilings.
•Do not place the heater below a socket outlet.
•Do not place the heater on moving vehicles or where it can tip over.
•Keep the heater away from flammable, combustible, explosive or
corrosive materials.
•Keep the heater away from curtains or similar materials that could
block the air inlet and outlet.
•Never block or restrict the air inlet and outlet for any reason.
•Keep the power cable away from heat sources, sharp edges, cutting
and moving parts.
•Do not expose directly to the weather or to excessive humidity.
•Do not place the heater in the immediate surroundings of a bath,
shower or swimming pool.
•Follow general and special fire safety regulations in force in all fields
of applications. In any case ensure the following minimum safety
clearances from materials or objects in the surroundings of the
heater:
•Side: 0.6 m
•Air inlet side: 1 m
•Top: 1.5 m
•Hot air outlet side: 3 m
•Floor: 0 m
•Floors and ceilings must be made of fireproof materials in the place
where the heater is operated.
•Do not connect direct-fired heaters to air ducts.
Instructions for Use
Start-up
Fill tank with clean fuel. Only use Diesel or Kerosene.
The fuel gauge on top of the tank allows to check fuel level
Connect the power cord plug to a 230 V 50 Hz earthed electrical
supply system.
Bekijk gratis de handleiding van NEO Tools 90-080, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | NEO Tools |
| Model | 90-080 |
| Categorie | Heater |
| Taal | Nederlands |
| Grootte | 39104 MB |
