Moulinex Optimo GM4110 handleiding
Handleiding
Je bekijkt pagina 26 van 29
24
• Start with the fabrics to be ironed at a low
temperature and finish with those which
need higher temperatures (••• or Max).
• To prime the steam circuit, either before
using the iron for the first time, or if you have
not used the steam function for a few
minutes, press the steam control button -
Fig.2 several times in a row, holding the iron
away from your clothes.This will enable any
cold water to be removed from the steam
circuit.
• For delicate fabrics, press the steam control
button (on the handle of the iron)
intermittently to avoid possible water
droplets appearing with the steam.
• If you are using starch, it should be sprayed
onto the reverse side of the fabric to be
ironed.
Be careful : mixed fibre fabrics : set the
ironing temperature to the setting for the
most delicate fabric. Woollen garments :
press repeatedly on the steam control
button - Fig.2 to obtain short bursts of
steam, without placing the iron on the
garment itself. This will avoid making the
fabric shiny.
DRY IRONING
• Do not press on the steam control button -
Fig.2.
VERTICAL STEAM IRONING
• Set the iron temperature dial and the steam
flow adjustment dial* to the max. position.
• Hang the garment on a coat hanger and
hold the fabric slightly taut with one hand.
• Press repeatedly on the steam control
button - Fig.2 (on the iron handle) moving
the iron from top to bottom - Fig.3.
Be careful : as steam is very hot, never
attempt to remove creases from a
garment while it is being worn, always
hang garments on a coat hanger. For
fabrics other than linen or cotton, hold the
iron a few centimetres from the garment to
avoid burning the fabric.
FILLING THE BOILER DURING USE
• VERY IMPORTANT : Before opening your
boiler, ensure that there is no more steam
left inside by pressing the steam control
button - Fig.2 located on the handle of the
iron and keep it pressed down until there is
no more steam.
Be careful : Never unscrew the boiler cap
while it’s still steaming.
• Stop the generator by pressing the on/off
switch and unplugging the plug.
• Slowly unscrew the boiler cap.
• Using a water jug, fill with maximum 1 litre of
water.
• Fill the boiler, taking care that the water
does not spill over. If this occurs, remove the
excess water.
• Replace the boiler cap, screwing on tightly.
Plug your generator into the mains, and
switch it on.
• Wait until the boiler heats up. After
approximately 8 minutes or when the steam
ready indicator light* comes on, the steam
is ready.
STORING THE GENERATOR
• Turn off at the main switch and unplug.
• Wind the electric cord around the cord tidy
- Fig.4.
• Place the iron on the rest.
• Storing the steam cord - Fig.5.
• Leave the steam generator to cool down
before putting it away if it is stored in a
cupboard or confined space.
• You can store your steam generator in
complete safety.
Be careful : Never place the iron on a
metal rest as this could damage it. Place it
on the iron-rest on the base unit : it has
non-slip pads and has been designed to
withstand high temperatures.
TYPE OF FABRIC
SETTING THE TEMPERATURE
DIAL
SETTING THE STEAM DIAL
(ACCORDING TO MODEL)
Linen, Cotton
•••
Wool, Silk, Viscose
••
Synthetic
(Polyester,Acetate,Acrylic,
Polyamide)
•
* depending on model
Pressing Optimo 00010789ok 13/07/06 15:28 Page 24
Bekijk gratis de handleiding van Moulinex Optimo GM4110, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Moulinex |
| Model | Optimo GM4110 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3181 MB |
