Mitsubishi MSZ-GS24NA handleiding

Airco

Mitsubishi

8 pagina's

PDF beschikbaar

Handleiding

1-4. INSTALLATION DIAGRAM

Outdoor unit installation

2-1/8 in. (55

mm) or more/

4-5/8 in. (118 mm)

or more for left and

left back piping

(using spacer)

ACCESSORIES

Check the following parts before installation.

(1) Installation plate 1

(2)

Attachment screws for the installa-

tion plate

4 × 25 mm

(3) Wireless remote controller 1

(4)

Felt tape

(For left or left-rear piping)

(5) Remote controller holder 1

(6)

Screws for the remote controller

holder

3.5 × 16 mm (Black)

(7) Battery (AAA) for (3) 2

(8) $LUFOHDQLQJ¿OWHU 2

FIELD-SUPPLIED PARTS

(A)

Indoor/outdoor unit connecting wire *1

(B) Extension pipe 1

(D) Wall hole cover 1

(E) Pipe attachment strap

2 to 5

(F) Screw for (E) 4 × 20 mm

2 to 5

(G) Piping tape 1

(H) Putty 1

(I)

Drain hose

(or soft PVC hose, 19/32 in. [15

mm] inner diameter or hard PVC

pipe VP16)

1 or 2

(J) Refrigerant oil 1

(K) Power supply cord *1 1

Units should be installed by licensed contractor

according to local code requirements.

Note:

*1 Place indoor/outdoor unit connecting wire (A)

and power supply cord (K) at least 3 ft. (1 m)

away from the TV antenna wire.

Unit: inch

Unit: mm

5-7/8 in.

(149 mm)

or more

After the leak test, apply insulating

material tightly so that there is no gap.

33-1/16

13-3/4~14-5/8

19-11/16

Air inlet

6-7/8

15-3/8

Air outlet

2-3/8 x 13/16 slot 1-9/16

840

175 500

Air inlet

390

330

349~371

Air outlet

2-10 x 21 slot

When the piping is to be attached to

a wall comprised of tin plate or metal

netting, use chemically treated wooden

piece 25/32 in. (20 mm) or thicker be-

tween the wall and the piping, or wrap

insulation vinyl tape 7 to 8 turns around

the piping.

To use existing piping, perform COOL

operation for 30 minutes and pump

down before removing the old air con-

GLWLRQHU5HPDNHÀDUHDFFRUGLQJWRWKH

dimension for new refrigerant.

3/8 in. (10 mm)

or more

4 in.

(100 mm)

or more

4 in.

(100 mm)

or more

14 in.

(350 mm)

or more

20 in.

(500 mm) *3

or more

5-1/2 in.

(140 mm)

or more

Drain piping for outdoor unit

Install the unit horizontally.

Do not use drain socket in cold regions. Drain may freeze and make the fan stop.

The outdoor unit produces condensate during the heating operation. Select the installation place to ensure to prevent the outdoor unit and/or the grounds from being wet by drain

water or damaged by frozen drain water.

Use the wall hole sleeve

door connecting wire (A)

from contacting metal parts

in the wall and to protect

the wiring from rodents.

Indoor unit

Wall hole

sleeve (C)

Cut off the

extra length.

3LSH¿[LQJEDQG

(E)

Wall hole cover (D)

Seal the wall hole

gap with putty (H).

Attach the pipe to

wall with pipe at-

tachment strap (E).

Fixing

screw (F)

*2 20 in. (500 mm) or more when front

and sides of unit are clear

clear *2

*3 When any 2 sides of left, right and

rear of unit are clear

5.9 to 7.5 ft. (1.8 to 2.3 m) from

WKHÀRRULVUHFRPPHQGHG

Air inletAir inlet

Note:

• The dimensions indicated in the arrows (

) above

show the required space to guarantee performance of

the air conditioner. Install the outdoor unit where the

maximum possible space can be provided, considering

later relocation, services, or repairs.

 7KHFRROLQJKHDWLQJSHUIRUPDQFHDQGWKHHI¿FLHQF\RI

power usage may fall about 10% at the place where short

cycle is likely occur due to poor ventilation. Installing the

air outlet guide (optional) can improve performances.

• If air from the outlet blows against the wall, it may cause

stains on the wall.

Do not take in the outlet air

discharged by other units directly.

15-3/4 in. or more

(400 mm or more)

39-3/8 in. or more

(1000 mm or more)

Bekijk gratis de handleiding van Mitsubishi MSZ-GS24NA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.