Mitsubishi MR-HS421EX handleiding
Handleiding
Je bekijkt pagina 6 van 24
6
From Installation to Operation
Install the refrigerator in the
following kind of location.
●
A place with good ventilation and not
exposed to direct sunlight or hot air
To keep good cooling performance and
reduce power costs.
● A place with low humidity
To prevent it from rusting.
● A strong and level place
To prevent vibration, noise, and ajar or
tilting doors.
To prevent deformation or discoloration of
the floor materials due to the weight or heat.
*If the floor materials are carpets, tatami
mats, wooden floors, PVC floors, etc.
and may deform or discolor, lay a
strong plate or board underneath.
● A place away from other devices
To prevent noise or video interference
with devices such as televisions.
● There should be at least 3 cm of
space on both the left and right
sides, at least 8 cm of space above
and at least 5 cm of space back.
To allow heat to dissipate from the top,
the back and the sides of the refrigerator.
Installation
Do not install the refrigerator
outdoors or in places exposed
to water or excessive humidity.
Water may cause insulation failure,
resulting in an electric shock or fire.
Water
prohibited
Leave space around the
refrigerator.
If refrigerant leaks, it may
accumulate and catch fire or
explode.
Follow the
instructions
Connect the Power Supply
Remove the energy label carefully. A glue residue may remain,
particularly if the label has been in place for a long period of time.
Apply either Eucalyptus or Tea Tree oil directly on any residue.
Do not allow the oil to run or drip onto plastic parts as it may
cause the plastic to degrade and potentially crack over time.
Allow the oil to sit for approximately 1-2 minutes, or until the
glue residue has softened.
Wipe off with a damp cloth.
If any residue remains, repeat the above process.
Rinse with clear water.
Dry thoroughly.
●
●
●
●
●
●
●
●
How to remove the energy label
5 cm. or more
3 cm. or more
8 cm. or more
Dedicated
outlet that meets
the specified rating.
Turn on the power of the
refrigerator as soon as
possible.
The refrigerator will not be
damaged even if you turn on
the power immediately after
the installation.
* Connect power supply soon after installing the
refrigerator
WARNING
Using outlets that do not meet the specified rating or
plugging in too many leads into a single socket can
cause heat buildup or fire.
● Use a dedicated outlet
● The refrigerator will not be damaged even if the power
is supplied soon after installation. It takes a while for
the refrigerator to cool, therefore supply power as soon
as possible.
● Electrical Connections
●
The refrigerator should always be plugged into its dedicated
electrical outlet. This will provide the best performance and prevent
electrical circuits from being overloaded and causing a fire.
Make sure that the electrical outlet provides the proper voltage.
Extension cords are not recommended.
●
If your refrigerator is installed in a high humidity location, not only
ground connection but also installation of the earth leakage breaker
is recommended.
●
If the power cord is damaged, purchase a new cord from
MITSUBISHI ELECTRIC SERVICE CENTRE. Make sure that
the power cord is designed for this model.
●
If the power cord is damaged, contact MITSUBISHI ELECTRIC
SERVICE CENTRE for the replacement, in order to avoid a hazard.
Make sure this unit is properly grounded.
Use a dedicated outlet for the power supply that meets the rating
specified on the rating label. (The rating label is located on the
refrigerator compartment.)
Bekijk gratis de handleiding van Mitsubishi MR-HS421EX, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Mitsubishi |
| Model | MR-HS421EX |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4766 MB |
